Export limit exceeded: 15245 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (15245 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-23115 | 1 Linux | 1 Linux Kernel | 2026-02-18 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: serial: Fix not set tty->port race condition Revert commit bfc467db60b7 ("serial: remove redundant tty_port_link_device()") because the tty_port_link_device() is not redundant: the tty->port has to be confured before we call uart_configure_port(), otherwise user-space can open console without TTY linked to the driver. This tty_port_link_device() was added explicitly to avoid this exact issue in commit fb2b90014d78 ("tty: link tty and port before configuring it as console"), so offending commit basically reverted the fix saying it is redundant without addressing the actual race condition presented there. Reproducible always as tty->port warning on Qualcomm SoC with most of devices disabled, so with very fast boot, and one serial device being the console: printk: legacy console [ttyMSM0] enabled printk: legacy console [ttyMSM0] enabled printk: legacy bootconsole [qcom_geni0] disabled printk: legacy bootconsole [qcom_geni0] disabled ------------[ cut here ]------------ tty_init_dev: ttyMSM driver does not set tty->port. This would crash the kernel. Fix the driver! WARNING: drivers/tty/tty_io.c:1414 at tty_init_dev.part.0+0x228/0x25c, CPU#2: systemd/1 Modules linked in: socinfo tcsrcc_eliza gcc_eliza sm3_ce fuse ipv6 CPU: 2 UID: 0 PID: 1 Comm: systemd Tainted: G S 6.19.0-rc4-next-20260108-00024-g2202f4d30aa8 #73 PREEMPT Tainted: [S]=CPU_OUT_OF_SPEC Hardware name: Qualcomm Technologies, Inc. Eliza (DT) ... tty_init_dev.part.0 (drivers/tty/tty_io.c:1414 (discriminator 11)) (P) tty_open (arch/arm64/include/asm/atomic_ll_sc.h:95 (discriminator 3) drivers/tty/tty_io.c:2073 (discriminator 3) drivers/tty/tty_io.c:2120 (discriminator 3)) chrdev_open (fs/char_dev.c:411) do_dentry_open (fs/open.c:962) vfs_open (fs/open.c:1094) do_open (fs/namei.c:4634) path_openat (fs/namei.c:4793) do_filp_open (fs/namei.c:4820) do_sys_openat2 (fs/open.c:1391 (discriminator 3)) ... Starting Network Name Resolution... Apparently the flow with this small Yocto-based ramdisk user-space is: driver (qcom_geni_serial.c): user-space: ============================ =========== qcom_geni_serial_probe() uart_add_one_port() serial_core_register_port() serial_core_add_one_port() uart_configure_port() register_console() | | open console | ... | tty_init_dev() | driver->ports[idx] is NULL | tty_port_register_device_attr_serdev() tty_port_link_device() <- set driver->ports[idx] | ||||
| CVE-2026-23163 | 1 Linux | 1 Linux Kernel | 2026-02-18 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix NULL pointer dereference in amdgpu_gmc_filter_faults_remove On APUs such as Raven and Renoir (GC 9.1.0, 9.2.2, 9.3.0), the ih1 and ih2 interrupt ring buffers are not initialized. This is by design, as these secondary IH rings are only available on discrete GPUs. See vega10_ih_sw_init() which explicitly skips ih1/ih2 initialization when AMD_IS_APU is set. However, amdgpu_gmc_filter_faults_remove() unconditionally uses ih1 to get the timestamp of the last interrupt entry. When retry faults are enabled on APUs (noretry=0), this function is called from the SVM page fault recovery path, resulting in a NULL pointer dereference when amdgpu_ih_decode_iv_ts_helper() attempts to access ih->ring[]. The crash manifests as: BUG: kernel NULL pointer dereference, address: 0000000000000004 RIP: 0010:amdgpu_ih_decode_iv_ts_helper+0x22/0x40 [amdgpu] Call Trace: amdgpu_gmc_filter_faults_remove+0x60/0x130 [amdgpu] svm_range_restore_pages+0xae5/0x11c0 [amdgpu] amdgpu_vm_handle_fault+0xc8/0x340 [amdgpu] gmc_v9_0_process_interrupt+0x191/0x220 [amdgpu] amdgpu_irq_dispatch+0xed/0x2c0 [amdgpu] amdgpu_ih_process+0x84/0x100 [amdgpu] This issue was exposed by commit 1446226d32a4 ("drm/amdgpu: Remove GC HW IP 9.3.0 from noretry=1") which changed the default for Renoir APU from noretry=1 to noretry=0, enabling retry fault handling and thus exercising the buggy code path. Fix this by adding a check for ih1.ring_size before attempting to use it. Also restore the soft_ih support from commit dd299441654f ("drm/amdgpu: Rework retry fault removal"). This is needed if the hardware doesn't support secondary HW IH rings. v2: additional updates (Alex) (cherry picked from commit 6ce8d536c80aa1f059e82184f0d1994436b1d526) | ||||
| CVE-2026-23165 | 1 Linux | 1 Linux Kernel | 2026-02-18 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: sfc: fix deadlock in RSS config read Since cited commit, core locks the net_device's rss_lock when handling ethtool -x command, so driver's implementation should not lock it again. Remove the latter. | ||||
| CVE-2026-23120 | 1 Linux | 1 Linux Kernel | 2026-02-18 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: l2tp: avoid one data-race in l2tp_tunnel_del_work() We should read sk->sk_socket only when dealing with kernel sockets. syzbot reported the following data-race: BUG: KCSAN: data-race in l2tp_tunnel_del_work / sk_common_release write to 0xffff88811c182b20 of 8 bytes by task 5365 on cpu 0: sk_set_socket include/net/sock.h:2092 [inline] sock_orphan include/net/sock.h:2118 [inline] sk_common_release+0xae/0x230 net/core/sock.c:4003 udp_lib_close+0x15/0x20 include/net/udp.h:325 inet_release+0xce/0xf0 net/ipv4/af_inet.c:437 __sock_release net/socket.c:662 [inline] sock_close+0x6b/0x150 net/socket.c:1455 __fput+0x29b/0x650 fs/file_table.c:468 ____fput+0x1c/0x30 fs/file_table.c:496 task_work_run+0x131/0x1a0 kernel/task_work.c:233 resume_user_mode_work include/linux/resume_user_mode.h:50 [inline] __exit_to_user_mode_loop kernel/entry/common.c:44 [inline] exit_to_user_mode_loop+0x1fe/0x740 kernel/entry/common.c:75 __exit_to_user_mode_prepare include/linux/irq-entry-common.h:226 [inline] syscall_exit_to_user_mode_prepare include/linux/irq-entry-common.h:256 [inline] syscall_exit_to_user_mode_work include/linux/entry-common.h:159 [inline] syscall_exit_to_user_mode include/linux/entry-common.h:194 [inline] do_syscall_64+0x1e1/0x2b0 arch/x86/entry/syscall_64.c:100 entry_SYSCALL_64_after_hwframe+0x77/0x7f read to 0xffff88811c182b20 of 8 bytes by task 827 on cpu 1: l2tp_tunnel_del_work+0x2f/0x1a0 net/l2tp/l2tp_core.c:1418 process_one_work kernel/workqueue.c:3257 [inline] process_scheduled_works+0x4ce/0x9d0 kernel/workqueue.c:3340 worker_thread+0x582/0x770 kernel/workqueue.c:3421 kthread+0x489/0x510 kernel/kthread.c:463 ret_from_fork+0x149/0x290 arch/x86/kernel/process.c:158 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:246 value changed: 0xffff88811b818000 -> 0x0000000000000000 | ||||
| CVE-2026-23172 | 1 Linux | 1 Linux Kernel | 2026-02-18 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: net: wwan: t7xx: fix potential skb->frags overflow in RX path When receiving data in the DPMAIF RX path, the t7xx_dpmaif_set_frag_to_skb() function adds page fragments to an skb without checking if the number of fragments has exceeded MAX_SKB_FRAGS. This could lead to a buffer overflow in skb_shinfo(skb)->frags[] array, corrupting adjacent memory and potentially causing kernel crashes or other undefined behavior. This issue was identified through static code analysis by comparing with a similar vulnerability fixed in the mt76 driver commit b102f0c522cf ("mt76: fix array overflow on receiving too many fragments for a packet"). The vulnerability could be triggered if the modem firmware sends packets with excessive fragments. While under normal protocol conditions (MTU 3080 bytes, BAT buffer 3584 bytes), a single packet should not require additional fragments, the kernel should not blindly trust firmware behavior. Malicious, buggy, or compromised firmware could potentially craft packets with more fragments than the kernel expects. Fix this by adding a bounds check before calling skb_add_rx_frag() to ensure nr_frags does not exceed MAX_SKB_FRAGS. The check must be performed before unmapping to avoid a page leak and double DMA unmap during device teardown. | ||||
| CVE-2026-23147 | 1 Linux | 1 Linux Kernel | 2026-02-18 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: btrfs: zlib: fix the folio leak on S390 hardware acceleration [BUG] After commit aa60fe12b4f4 ("btrfs: zlib: refactor S390x HW acceleration buffer preparation"), we no longer release the folio of the page cache of folio returned by btrfs_compress_filemap_get_folio() for S390 hardware acceleration path. [CAUSE] Before that commit, we call kumap_local() and folio_put() after handling each folio. Although the timing is not ideal (it release previous folio at the beginning of the loop, and rely on some extra cleanup out of the loop), it at least handles the folio release correctly. Meanwhile the refactored code is easier to read, it lacks the call to release the filemap folio. [FIX] Add the missing folio_put() for copy_data_into_buffer(). | ||||
| CVE-2026-23167 | 1 Linux | 1 Linux Kernel | 2026-02-18 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: nfc: nci: Fix race between rfkill and nci_unregister_device(). syzbot reported the splat below [0] without a repro. It indicates that struct nci_dev.cmd_wq had been destroyed before nci_close_device() was called via rfkill. nci_dev.cmd_wq is only destroyed in nci_unregister_device(), which (I think) was called from virtual_ncidev_close() when syzbot close()d an fd of virtual_ncidev. The problem is that nci_unregister_device() destroys nci_dev.cmd_wq first and then calls nfc_unregister_device(), which removes the device from rfkill by rfkill_unregister(). So, the device is still visible via rfkill even after nci_dev.cmd_wq is destroyed. Let's unregister the device from rfkill first in nci_unregister_device(). Note that we cannot call nfc_unregister_device() before nci_close_device() because 1) nfc_unregister_device() calls device_del() which frees all memory allocated by devm_kzalloc() and linked to ndev->conn_info_list 2) nci_rx_work() could try to queue nci_conn_info to ndev->conn_info_list which could be leaked Thus, nfc_unregister_device() is split into two functions so we can remove rfkill interfaces only before nci_close_device(). [0]: DEBUG_LOCKS_WARN_ON(1) WARNING: kernel/locking/lockdep.c:238 at hlock_class kernel/locking/lockdep.c:238 [inline], CPU#0: syz.0.8675/6349 WARNING: kernel/locking/lockdep.c:238 at check_wait_context kernel/locking/lockdep.c:4854 [inline], CPU#0: syz.0.8675/6349 WARNING: kernel/locking/lockdep.c:238 at __lock_acquire+0x39d/0x2cf0 kernel/locking/lockdep.c:5187, CPU#0: syz.0.8675/6349 Modules linked in: CPU: 0 UID: 0 PID: 6349 Comm: syz.0.8675 Not tainted syzkaller #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/13/2026 RIP: 0010:hlock_class kernel/locking/lockdep.c:238 [inline] RIP: 0010:check_wait_context kernel/locking/lockdep.c:4854 [inline] RIP: 0010:__lock_acquire+0x3a4/0x2cf0 kernel/locking/lockdep.c:5187 Code: 18 00 4c 8b 74 24 08 75 27 90 e8 17 f2 fc 02 85 c0 74 1c 83 3d 50 e0 4e 0e 00 75 13 48 8d 3d 43 f7 51 0e 48 c7 c6 8b 3a de 8d <67> 48 0f b9 3a 90 31 c0 0f b6 98 c4 00 00 00 41 8b 45 20 25 ff 1f RSP: 0018:ffffc9000c767680 EFLAGS: 00010046 RAX: 0000000000000001 RBX: 0000000000040000 RCX: 0000000000080000 RDX: ffffc90013080000 RSI: ffffffff8dde3a8b RDI: ffffffff8ff24ca0 RBP: 0000000000000003 R08: ffffffff8fef35a3 R09: 1ffffffff1fde6b4 R10: dffffc0000000000 R11: fffffbfff1fde6b5 R12: 00000000000012a2 R13: ffff888030338ba8 R14: ffff888030338000 R15: ffff888030338b30 FS: 00007fa5995f66c0(0000) GS:ffff8881256f8000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f7e72f842d0 CR3: 00000000485a0000 CR4: 00000000003526f0 Call Trace: <TASK> lock_acquire+0x106/0x330 kernel/locking/lockdep.c:5868 touch_wq_lockdep_map+0xcb/0x180 kernel/workqueue.c:3940 __flush_workqueue+0x14b/0x14f0 kernel/workqueue.c:3982 nci_close_device+0x302/0x630 net/nfc/nci/core.c:567 nci_dev_down+0x3b/0x50 net/nfc/nci/core.c:639 nfc_dev_down+0x152/0x290 net/nfc/core.c:161 nfc_rfkill_set_block+0x2d/0x100 net/nfc/core.c:179 rfkill_set_block+0x1d2/0x440 net/rfkill/core.c:346 rfkill_fop_write+0x461/0x5a0 net/rfkill/core.c:1301 vfs_write+0x29a/0xb90 fs/read_write.c:684 ksys_write+0x150/0x270 fs/read_write.c:738 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xe2/0xf80 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7fa59b39acb9 Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 e8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007fa5995f6028 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 00007fa59b615fa0 RCX: 00007fa59b39acb9 RDX: 0000000000000008 RSI: 0000200000000080 RDI: 0000000000000007 RBP: 00007fa59b408bf7 R08: ---truncated--- | ||||
| CVE-2026-23173 | 1 Linux | 1 Linux Kernel | 2026-02-18 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: TC, delete flows only for existing peers When deleting TC steering flows, iterate only over actual devcom peers instead of assuming all possible ports exist. This avoids touching non-existent peers and ensures cleanup is limited to devices the driver is currently connected to. BUG: kernel NULL pointer dereference, address: 0000000000000008 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page PGD 133c8a067 P4D 0 Oops: Oops: 0002 [#1] SMP CPU: 19 UID: 0 PID: 2169 Comm: tc Not tainted 6.18.0+ #156 NONE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:mlx5e_tc_del_fdb_peers_flow+0xbe/0x200 [mlx5_core] Code: 00 00 a8 08 74 a8 49 8b 46 18 f6 c4 02 74 9f 4c 8d bf a0 12 00 00 4c 89 ff e8 0e e7 96 e1 49 8b 44 24 08 49 8b 0c 24 4c 89 ff <48> 89 41 08 48 89 08 49 89 2c 24 49 89 5c 24 08 e8 7d ce 96 e1 49 RSP: 0018:ff11000143867528 EFLAGS: 00010246 RAX: 0000000000000000 RBX: dead000000000122 RCX: 0000000000000000 RDX: ff11000143691580 RSI: ff110001026e5000 RDI: ff11000106f3d2a0 RBP: dead000000000100 R08: 00000000000003fd R09: 0000000000000002 R10: ff11000101c75690 R11: ff1100085faea178 R12: ff11000115f0ae78 R13: 0000000000000000 R14: ff11000115f0a800 R15: ff11000106f3d2a0 FS: 00007f35236bf740(0000) GS:ff110008dc809000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000008 CR3: 0000000157a01001 CR4: 0000000000373eb0 Call Trace: <TASK> mlx5e_tc_del_flow+0x46/0x270 [mlx5_core] mlx5e_flow_put+0x25/0x50 [mlx5_core] mlx5e_delete_flower+0x2a6/0x3e0 [mlx5_core] tc_setup_cb_reoffload+0x20/0x80 fl_reoffload+0x26f/0x2f0 [cls_flower] ? mlx5e_tc_reoffload_flows_work+0xc0/0xc0 [mlx5_core] ? mlx5e_tc_reoffload_flows_work+0xc0/0xc0 [mlx5_core] tcf_block_playback_offloads+0x9e/0x1c0 tcf_block_unbind+0x7b/0xd0 tcf_block_setup+0x186/0x1d0 tcf_block_offload_cmd.isra.0+0xef/0x130 tcf_block_offload_unbind+0x43/0x70 __tcf_block_put+0x85/0x160 ingress_destroy+0x32/0x110 [sch_ingress] __qdisc_destroy+0x44/0x100 qdisc_graft+0x22b/0x610 tc_get_qdisc+0x183/0x4d0 rtnetlink_rcv_msg+0x2d7/0x3d0 ? rtnl_calcit.isra.0+0x100/0x100 netlink_rcv_skb+0x53/0x100 netlink_unicast+0x249/0x320 ? __alloc_skb+0x102/0x1f0 netlink_sendmsg+0x1e3/0x420 __sock_sendmsg+0x38/0x60 ____sys_sendmsg+0x1ef/0x230 ? copy_msghdr_from_user+0x6c/0xa0 ___sys_sendmsg+0x7f/0xc0 ? ___sys_recvmsg+0x8a/0xc0 ? __sys_sendto+0x119/0x180 __sys_sendmsg+0x61/0xb0 do_syscall_64+0x55/0x640 entry_SYSCALL_64_after_hwframe+0x4b/0x53 RIP: 0033:0x7f35238bb764 Code: 15 b9 86 0c 00 f7 d8 64 89 02 b8 ff ff ff ff eb bf 0f 1f 44 00 00 f3 0f 1e fa 80 3d e5 08 0d 00 00 74 13 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 4c c3 0f 1f 00 55 48 89 e5 48 83 ec 20 89 55 RSP: 002b:00007ffed4c35638 EFLAGS: 00000202 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 000055a2efcc75e0 RCX: 00007f35238bb764 RDX: 0000000000000000 RSI: 00007ffed4c356a0 RDI: 0000000000000003 RBP: 00007ffed4c35710 R08: 0000000000000010 R09: 00007f3523984b20 R10: 0000000000000004 R11: 0000000000000202 R12: 00007ffed4c35790 R13: 000000006947df8f R14: 000055a2efcc75e0 R15: 00007ffed4c35780 | ||||
| CVE-2026-23160 | 1 Linux | 1 Linux Kernel | 2026-02-18 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: octeon_ep: Fix memory leak in octep_device_setup() In octep_device_setup(), if octep_ctrl_net_init() fails, the function returns directly without unmapping the mapped resources and freeing the allocated configuration memory. Fix this by jumping to the unsupported_dev label, which performs the necessary cleanup. This aligns with the error handling logic of other paths in this function. Compile tested only. Issue found using a prototype static analysis tool and code review. | ||||
| CVE-2026-23113 | 1 Linux | 1 Linux Kernel | 2026-02-18 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: io_uring/io-wq: check IO_WQ_BIT_EXIT inside work run loop Currently this is checked before running the pending work. Normally this is quite fine, as work items either end up blocking (which will create a new worker for other items), or they complete fairly quickly. But syzbot reports an issue where io-wq takes seemingly forever to exit, and with a bit of debugging, this turns out to be because it queues a bunch of big (2GB - 4096b) reads with a /dev/msr* file. Since this file type doesn't support ->read_iter(), loop_rw_iter() ends up handling them. Each read returns 16MB of data read, which takes 20 (!!) seconds. With a bunch of these pending, processing the whole chain can take a long time. Easily longer than the syzbot uninterruptible sleep timeout of 140 seconds. This then triggers a complaint off the io-wq exit path: INFO: task syz.4.135:6326 blocked for more than 143 seconds. Not tainted syzkaller #0 Blocked by coredump. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:syz.4.135 state:D stack:26824 pid:6326 tgid:6324 ppid:5957 task_flags:0x400548 flags:0x00080000 Call Trace: <TASK> context_switch kernel/sched/core.c:5256 [inline] __schedule+0x1139/0x6150 kernel/sched/core.c:6863 __schedule_loop kernel/sched/core.c:6945 [inline] schedule+0xe7/0x3a0 kernel/sched/core.c:6960 schedule_timeout+0x257/0x290 kernel/time/sleep_timeout.c:75 do_wait_for_common kernel/sched/completion.c:100 [inline] __wait_for_common+0x2fc/0x4e0 kernel/sched/completion.c:121 io_wq_exit_workers io_uring/io-wq.c:1328 [inline] io_wq_put_and_exit+0x271/0x8a0 io_uring/io-wq.c:1356 io_uring_clean_tctx+0x10d/0x190 io_uring/tctx.c:203 io_uring_cancel_generic+0x69c/0x9a0 io_uring/cancel.c:651 io_uring_files_cancel include/linux/io_uring.h:19 [inline] do_exit+0x2ce/0x2bd0 kernel/exit.c:911 do_group_exit+0xd3/0x2a0 kernel/exit.c:1112 get_signal+0x2671/0x26d0 kernel/signal.c:3034 arch_do_signal_or_restart+0x8f/0x7e0 arch/x86/kernel/signal.c:337 __exit_to_user_mode_loop kernel/entry/common.c:41 [inline] exit_to_user_mode_loop+0x8c/0x540 kernel/entry/common.c:75 __exit_to_user_mode_prepare include/linux/irq-entry-common.h:226 [inline] syscall_exit_to_user_mode_prepare include/linux/irq-entry-common.h:256 [inline] syscall_exit_to_user_mode_work include/linux/entry-common.h:159 [inline] syscall_exit_to_user_mode include/linux/entry-common.h:194 [inline] do_syscall_64+0x4ee/0xf80 arch/x86/entry/syscall_64.c:100 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7fa02738f749 RSP: 002b:00007fa0281ae0e8 EFLAGS: 00000246 ORIG_RAX: 00000000000000ca RAX: fffffffffffffe00 RBX: 00007fa0275e6098 RCX: 00007fa02738f749 RDX: 0000000000000000 RSI: 0000000000000080 RDI: 00007fa0275e6098 RBP: 00007fa0275e6090 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00007fa0275e6128 R14: 00007fff14e4fcb0 R15: 00007fff14e4fd98 There's really nothing wrong here, outside of processing these reads will take a LONG time. However, we can speed up the exit by checking the IO_WQ_BIT_EXIT inside the io_worker_handle_work() loop, as syzbot will exit the ring after queueing up all of these reads. Then once the first item is processed, io-wq will simply cancel the rest. That should avoid syzbot running into this complaint again. | ||||
| CVE-2026-23152 | 1 Linux | 1 Linux Kernel | 2026-02-18 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: correctly decode TTLM with default link map TID-To-Link Mapping (TTLM) elements do not contain any link mapping presence indicator if a default mapping is used and parsing needs to be skipped. Note that access points should not explicitly report an advertised TTLM with a default mapping as that is the implied mapping if the element is not included, this is even the case when switching back to the default mapping. However, mac80211 would incorrectly parse the frame and would also read one byte beyond the end of the element. | ||||
| CVE-2026-23164 | 1 Linux | 1 Linux Kernel | 2026-02-18 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: rocker: fix memory leak in rocker_world_port_post_fini() In rocker_world_port_pre_init(), rocker_port->wpriv is allocated with kzalloc(wops->port_priv_size, GFP_KERNEL). However, in rocker_world_port_post_fini(), the memory is only freed when wops->port_post_fini callback is set: if (!wops->port_post_fini) return; wops->port_post_fini(rocker_port); kfree(rocker_port->wpriv); Since rocker_ofdpa_ops does not implement port_post_fini callback (it is NULL), the wpriv memory allocated for each port is never freed when ports are removed. This leads to a memory leak of sizeof(struct ofdpa_port) bytes per port on every device removal. Fix this by always calling kfree(rocker_port->wpriv) regardless of whether the port_post_fini callback exists. | ||||
| CVE-2026-23153 | 1 Linux | 1 Linux Kernel | 2026-02-18 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: firewire: core: fix race condition against transaction list The list of transaction is enumerated without acquiring card lock when processing AR response event. This causes a race condition bug when processing AT request completion event concurrently. This commit fixes the bug by put timer start for split transaction expiration into the scope of lock. The value of jiffies in card structure is referred before acquiring the lock. | ||||
| CVE-2026-23170 | 1 Linux | 1 Linux Kernel | 2026-02-18 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: drm/imx/tve: fix probe device leak Make sure to drop the reference taken to the DDC device during probe on probe failure (e.g. probe deferral) and on driver unbind. | ||||
| CVE-2026-23192 | 1 Linux | 1 Linux Kernel | 2026-02-18 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: linkwatch: use __dev_put() in callers to prevent UAF After linkwatch_do_dev() calls __dev_put() to release the linkwatch reference, the device refcount may drop to 1. At this point, netdev_run_todo() can proceed (since linkwatch_sync_dev() sees an empty list and returns without blocking), wait for the refcount to become 1 via netdev_wait_allrefs_any(), and then free the device via kobject_put(). This creates a use-after-free when __linkwatch_run_queue() tries to call netdev_unlock_ops() on the already-freed device. Note that adding netdev_lock_ops()/netdev_unlock_ops() pair in netdev_run_todo() before kobject_put() would not work, because netdev_lock_ops() is conditional - it only locks when netdev_need_ops_lock() returns true. If the device doesn't require ops_lock, linkwatch won't hold any lock, and netdev_run_todo() acquiring the lock won't provide synchronization. Fix this by moving __dev_put() from linkwatch_do_dev() to its callers. The device reference logically pairs with de-listing the device, so it's reasonable for the caller that did the de-listing to release it. This allows placing __dev_put() after all device accesses are complete, preventing UAF. The bug can be reproduced by adding mdelay(2000) after linkwatch_do_dev() in __linkwatch_run_queue(), then running: ip tuntap add mode tun name tun_test ip link set tun_test up ip link set tun_test carrier off ip link set tun_test carrier on sleep 0.5 ip tuntap del mode tun name tun_test KASAN report: ================================================================== BUG: KASAN: use-after-free in netdev_need_ops_lock include/net/netdev_lock.h:33 [inline] BUG: KASAN: use-after-free in netdev_unlock_ops include/net/netdev_lock.h:47 [inline] BUG: KASAN: use-after-free in __linkwatch_run_queue+0x865/0x8a0 net/core/link_watch.c:245 Read of size 8 at addr ffff88804de5c008 by task kworker/u32:10/8123 CPU: 0 UID: 0 PID: 8123 Comm: kworker/u32:10 Not tainted syzkaller #0 PREEMPT(full) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Workqueue: events_unbound linkwatch_event Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x100/0x190 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0x156/0x4c9 mm/kasan/report.c:482 kasan_report+0xdf/0x1a0 mm/kasan/report.c:595 netdev_need_ops_lock include/net/netdev_lock.h:33 [inline] netdev_unlock_ops include/net/netdev_lock.h:47 [inline] __linkwatch_run_queue+0x865/0x8a0 net/core/link_watch.c:245 linkwatch_event+0x8f/0xc0 net/core/link_watch.c:304 process_one_work+0x9c2/0x1840 kernel/workqueue.c:3257 process_scheduled_works kernel/workqueue.c:3340 [inline] worker_thread+0x5da/0xe40 kernel/workqueue.c:3421 kthread+0x3b3/0x730 kernel/kthread.c:463 ret_from_fork+0x754/0xaf0 arch/x86/kernel/process.c:158 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:246 </TASK> ================================================================== | ||||
| CVE-2026-23197 | 1 Linux | 1 Linux Kernel | 2026-02-18 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: i2c: imx: preserve error state in block data length handler When a block read returns an invalid length, zero or >I2C_SMBUS_BLOCK_MAX, the length handler sets the state to IMX_I2C_STATE_FAILED. However, i2c_imx_master_isr() unconditionally overwrites this with IMX_I2C_STATE_READ_CONTINUE, causing an endless read loop that overruns buffers and crashes the system. Guard the state transition to preserve error states set by the length handler. | ||||
| CVE-2026-23204 | 1 Linux | 1 Linux Kernel | 2026-02-18 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: net/sched: cls_u32: use skb_header_pointer_careful() skb_header_pointer() does not fully validate negative @offset values. Use skb_header_pointer_careful() instead. GangMin Kim provided a report and a repro fooling u32_classify(): BUG: KASAN: slab-out-of-bounds in u32_classify+0x1180/0x11b0 net/sched/cls_u32.c:221 | ||||
| CVE-2026-23206 | 1 Linux | 1 Linux Kernel | 2026-02-18 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: dpaa2-switch: prevent ZERO_SIZE_PTR dereference when num_ifs is zero The driver allocates arrays for ports, FDBs, and filter blocks using kcalloc() with ethsw->sw_attr.num_ifs as the element count. When the device reports zero interfaces (either due to hardware configuration or firmware issues), kcalloc(0, ...) returns ZERO_SIZE_PTR (0x10) instead of NULL. Later in dpaa2_switch_probe(), the NAPI initialization unconditionally accesses ethsw->ports[0]->netdev, which attempts to dereference ZERO_SIZE_PTR (address 0x10), resulting in a kernel panic. Add a check to ensure num_ifs is greater than zero after retrieving device attributes. This prevents the zero-sized allocations and subsequent invalid pointer dereference. | ||||
| CVE-2026-23198 | 1 Linux | 1 Linux Kernel | 2026-02-18 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: KVM: Don't clobber irqfd routing type when deassigning irqfd When deassigning a KVM_IRQFD, don't clobber the irqfd's copy of the IRQ's routing entry as doing so breaks kvm_arch_irq_bypass_del_producer() on x86 and arm64, which explicitly look for KVM_IRQ_ROUTING_MSI. Instead, to handle a concurrent routing update, verify that the irqfd is still active before consuming the routing information. As evidenced by the x86 and arm64 bugs, and another bug in kvm_arch_update_irqfd_routing() (see below), clobbering the entry type without notifying arch code is surprising and error prone. As a bonus, checking that the irqfd is active provides a convenient location for documenting _why_ KVM must not consume the routing entry for an irqfd that is in the process of being deassigned: once the irqfd is deleted from the list (which happens *before* the eventfd is detached), it will no longer receive updates via kvm_irq_routing_update(), and so KVM could deliver an event using stale routing information (relative to KVM_SET_GSI_ROUTING returning to userspace). As an even better bonus, explicitly checking for the irqfd being active fixes a similar bug to the one the clobbering is trying to prevent: if an irqfd is deactivated, and then its routing is changed, kvm_irq_routing_update() won't invoke kvm_arch_update_irqfd_routing() (because the irqfd isn't in the list). And so if the irqfd is in bypass mode, IRQs will continue to be posted using the old routing information. As for kvm_arch_irq_bypass_del_producer(), clobbering the routing type results in KVM incorrectly keeping the IRQ in bypass mode, which is especially problematic on AMD as KVM tracks IRQs that are being posted to a vCPU in a list whose lifetime is tied to the irqfd. Without the help of KASAN to detect use-after-free, the most common sympton on AMD is a NULL pointer deref in amd_iommu_update_ga() due to the memory for irqfd structure being re-allocated and zeroed, resulting in irqfd->irq_bypass_data being NULL when read by avic_update_iommu_vcpu_affinity(): BUG: kernel NULL pointer dereference, address: 0000000000000018 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 40cf2b9067 P4D 40cf2b9067 PUD 408362a067 PMD 0 Oops: Oops: 0000 [#1] SMP CPU: 6 UID: 0 PID: 40383 Comm: vfio_irq_test Tainted: G U W O 6.19.0-smp--5dddc257e6b2-irqfd #31 NONE Tainted: [U]=USER, [W]=WARN, [O]=OOT_MODULE Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 34.78.2-0 09/05/2025 RIP: 0010:amd_iommu_update_ga+0x19/0xe0 Call Trace: <TASK> avic_update_iommu_vcpu_affinity+0x3d/0x90 [kvm_amd] __avic_vcpu_load+0xf4/0x130 [kvm_amd] kvm_arch_vcpu_load+0x89/0x210 [kvm] vcpu_load+0x30/0x40 [kvm] kvm_arch_vcpu_ioctl_run+0x45/0x620 [kvm] kvm_vcpu_ioctl+0x571/0x6a0 [kvm] __se_sys_ioctl+0x6d/0xb0 do_syscall_64+0x6f/0x9d0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 RIP: 0033:0x46893b </TASK> ---[ end trace 0000000000000000 ]--- If AVIC is inhibited when the irfd is deassigned, the bug will manifest as list corruption, e.g. on the next irqfd assignment. list_add corruption. next->prev should be prev (ffff8d474d5cd588), but was 0000000000000000. (next=ffff8d8658f86530). ------------[ cut here ]------------ kernel BUG at lib/list_debug.c:31! Oops: invalid opcode: 0000 [#1] SMP CPU: 128 UID: 0 PID: 80818 Comm: vfio_irq_test Tainted: G U W O 6.19.0-smp--f19dc4d680ba-irqfd #28 NONE Tainted: [U]=USER, [W]=WARN, [O]=OOT_MODULE Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 34.78.2-0 09/05/2025 RIP: 0010:__list_add_valid_or_report+0x97/0xc0 Call Trace: <TASK> avic_pi_update_irte+0x28e/0x2b0 [kvm_amd] kvm_pi_update_irte+0xbf/0x190 [kvm] kvm_arch_irq_bypass_add_producer+0x72/0x90 [kvm] irq_bypass_register_consumer+0xcd/0x170 [irqbypa ---truncated--- | ||||
| CVE-2025-71224 | 1 Linux | 1 Linux Kernel | 2026-02-18 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: ocb: skip rx_no_sta when interface is not joined ieee80211_ocb_rx_no_sta() assumes a valid channel context, which is only present after JOIN_OCB. RX may run before JOIN_OCB is executed, in which case the OCB interface is not operational. Skip RX peer handling when the interface is not joined to avoid warnings in the RX path. | ||||