| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcm80211: handle pmk_op allocation failure
The kzalloc() in brcmf_pmksa_v3_op() will return null if the
physical memory has run out. As a result, if we dereference
the null value, the null pointer dereference bug will happen.
Return -ENOMEM from brcmf_pmksa_v3_op() if kzalloc() fails
for pmk_op. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: fix phy_get_internal_delay accessing an empty array
The phy_get_internal_delay function could try to access to an empty
array in the case that the driver is calling phy_get_internal_delay
without defining delay_values and rx-internal-delay-ps or
tx-internal-delay-ps is defined to 0 in the device-tree.
This will lead to "unable to handle kernel NULL pointer dereference at
virtual address 0". To avoid this kernel oops, the test should be delay
>= 0. As there is already delay < 0 test just before, the test could
only be size == 0. |
| In the Linux kernel, the following vulnerability has been resolved:
nfp: flower: handle acti_netdevs allocation failure
The kmalloc_array() in nfp_fl_lag_do_work() will return null, if
the physical memory has run out. As a result, if we dereference
the acti_netdevs, the null pointer dereference bugs will happen.
This patch adds a check to judge whether allocation failure occurs.
If it happens, the delayed work will be rescheduled and try again. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix potential NULL pointer dereferences in 'dcn10_set_output_transfer_func()'
The 'stream' pointer is used in dcn10_set_output_transfer_func() before
the check if 'stream' is NULL.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn10/dcn10_hwseq.c:1892 dcn10_set_output_transfer_func() warn: variable dereferenced before check 'stream' (see line 1875) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: fix NULL checks for adev->dm.dc in amdgpu_dm_fini()
Since 'adev->dm.dc' in amdgpu_dm_fini() might turn out to be NULL
before the call to dc_enable_dmub_notifications(), check
beforehand to ensure there will not be a possible NULL-ptr-deref
there.
Also, since commit 1e88eb1b2c25 ("drm/amd/display: Drop
CONFIG_DRM_AMD_DC_HDCP") there are two separate checks for NULL in
'adev->dm.dc' before dc_deinit_callbacks() and dc_dmub_srv_destroy().
Clean up by combining them all under one 'if'.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Add 'replay' NULL check in 'edp_set_replay_allow_active()'
In the first if statement, we're checking if 'replay' is NULL. But in
the second if statement, we're not checking if 'replay' is NULL again
before calling replay->funcs->replay_set_power_opt().
if (replay == NULL && force_static)
return false;
...
if (link->replay_settings.replay_feature_enabled &&
replay->funcs->replay_set_power_opt) {
replay->funcs->replay_set_power_opt(replay, *power_opts, panel_inst);
link->replay_settings.replay_power_opt_active = *power_opts;
}
If 'replay' is NULL, this will cause a null pointer dereference.
Fixes the below found by smatch:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_edp_panel_control.c:895 edp_set_replay_allow_active() error: we previously assumed 'replay' could be null (see line 887) |
| In the Linux kernel, the following vulnerability has been resolved:
clk: Fix clk_core_get NULL dereference
It is possible for clk_core_get to dereference a NULL in the following
sequence:
clk_core_get()
of_clk_get_hw_from_clkspec()
__of_clk_get_hw_from_provider()
__clk_get_hw()
__clk_get_hw() can return NULL which is dereferenced by clk_core_get() at
hw->core.
Prior to commit dde4eff47c82 ("clk: Look for parents with clkdev based
clk_lookups") the check IS_ERR_OR_NULL() was performed which would have
caught the NULL.
Reading the description of this function it talks about returning NULL but
that cannot be so at the moment.
Update the function to check for hw before dereferencing it and return NULL
if hw is NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
clk: zynq: Prevent null pointer dereference caused by kmalloc failure
The kmalloc() in zynq_clk_setup() will return null if the
physical memory has run out. As a result, if we use snprintf()
to write data to the null address, the null pointer dereference
bug will happen.
This patch uses a stack variable to replace the kmalloc(). |
| In the Linux kernel, the following vulnerability has been resolved:
spi: spi-mt65xx: Fix NULL pointer access in interrupt handler
The TX buffer in spi_transfer can be a NULL pointer, so the interrupt
handler may end up writing to the invalid memory and cause crashes.
Add a check to trans->tx_buf before using it. |
| In the Linux kernel, the following vulnerability has been resolved:
nbd: null check for nla_nest_start
nla_nest_start() may fail and return NULL. Insert a check and set errno
based on other call sites within the same source code. |
| In the Linux kernel, the following vulnerability has been resolved:
nouveau: fix instmem race condition around ptr stores
Running a lot of VK CTS in parallel against nouveau, once every
few hours you might see something like this crash.
BUG: kernel NULL pointer dereference, address: 0000000000000008
PGD 8000000114e6e067 P4D 8000000114e6e067 PUD 109046067 PMD 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 7 PID: 53891 Comm: deqp-vk Not tainted 6.8.0-rc6+ #27
Hardware name: Gigabyte Technology Co., Ltd. Z390 I AORUS PRO WIFI/Z390 I AORUS PRO WIFI-CF, BIOS F8 11/05/2021
RIP: 0010:gp100_vmm_pgt_mem+0xe3/0x180 [nouveau]
Code: c7 48 01 c8 49 89 45 58 85 d2 0f 84 95 00 00 00 41 0f b7 46 12 49 8b 7e 08 89 da 42 8d 2c f8 48 8b 47 08 41 83 c7 01 48 89 ee <48> 8b 40 08 ff d0 0f 1f 00 49 8b 7e 08 48 89 d9 48 8d 75 04 48 c1
RSP: 0000:ffffac20c5857838 EFLAGS: 00010202
RAX: 0000000000000000 RBX: 00000000004d8001 RCX: 0000000000000001
RDX: 00000000004d8001 RSI: 00000000000006d8 RDI: ffffa07afe332180
RBP: 00000000000006d8 R08: ffffac20c5857ad0 R09: 0000000000ffff10
R10: 0000000000000001 R11: ffffa07af27e2de0 R12: 000000000000001c
R13: ffffac20c5857ad0 R14: ffffa07a96fe9040 R15: 000000000000001c
FS: 00007fe395eed7c0(0000) GS:ffffa07e2c980000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 000000011febe001 CR4: 00000000003706f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
...
? gp100_vmm_pgt_mem+0xe3/0x180 [nouveau]
? gp100_vmm_pgt_mem+0x37/0x180 [nouveau]
nvkm_vmm_iter+0x351/0xa20 [nouveau]
? __pfx_nvkm_vmm_ref_ptes+0x10/0x10 [nouveau]
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
? __lock_acquire+0x3ed/0x2170
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
nvkm_vmm_ptes_get_map+0xc2/0x100 [nouveau]
? __pfx_nvkm_vmm_ref_ptes+0x10/0x10 [nouveau]
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
nvkm_vmm_map_locked+0x224/0x3a0 [nouveau]
Adding any sort of useful debug usually makes it go away, so I hand
wrote the function in a line, and debugged the asm.
Every so often pt->memory->ptrs is NULL. This ptrs ptr is set in
the nv50_instobj_acquire called from nvkm_kmap.
If Thread A and Thread B both get to nv50_instobj_acquire around
the same time, and Thread A hits the refcount_set line, and in
lockstep thread B succeeds at refcount_inc_not_zero, there is a
chance the ptrs value won't have been stored since refcount_set
is unordered. Force a memory barrier here, I picked smp_mb, since
we want it on all CPUs and it's write followed by a read.
v2: use paired smp_rmb/smp_wmb. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: max310x: fix NULL pointer dereference in I2C instantiation
When trying to instantiate a max14830 device from userspace:
echo max14830 0x60 > /sys/bus/i2c/devices/i2c-2/new_device
we get the following error:
Unable to handle kernel NULL pointer dereference at virtual address...
...
Call trace:
max310x_i2c_probe+0x48/0x170 [max310x]
i2c_device_probe+0x150/0x2a0
...
Add check for validity of devtype to prevent the error, and abort probe
with a meaningful error message. |
| In the Linux kernel, the following vulnerability has been resolved:
powercap: intel_rapl: Fix a NULL pointer dereference
A NULL pointer dereference is triggered when probing the MMIO RAPL
driver on platforms with CPU ID not listed in intel_rapl_common CPU
model list.
This is because the intel_rapl_common module still probes on such
platforms even if 'defaults_msr' is not set after commit 1488ac990ac8
("powercap: intel_rapl: Allow probing without CPUID match"). Thus the
MMIO RAPL rp->priv->defaults is NULL when registering to RAPL framework.
Fix the problem by adding sanity check to ensure rp->priv->rapl_defaults
is always valid. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: xhci: Add error handling in xhci_map_urb_for_dma
Currently xhci_map_urb_for_dma() creates a temporary buffer and copies
the SG list to the new linear buffer. But if the kzalloc_node() fails,
then the following sg_pcopy_to_buffer() can lead to crash since it
tries to memcpy to NULL pointer.
So return -ENOMEM if kzalloc returns null pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
wireguard: netlink: access device through ctx instead of peer
The previous commit fixed a bug that led to a NULL peer->device being
dereferenced. It's actually easier and faster performance-wise to
instead get the device from ctx->wg. This semantically makes more sense
too, since ctx->wg->peer_allowedips.seq is compared with
ctx->allowedips_seq, basing them both in ctx. This also acts as a
defence in depth provision against freed peers. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/pm: Fix NULL pointer dereference when get power limit
Because powerplay_table initialization is skipped under
sriov case, We check and set default lower and upper OD
value if powerplay_table is NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: qcom: at803x: fix kernel panic with at8031_probe
On reworking and splitting the at803x driver, in splitting function of
at803x PHYs it was added a NULL dereference bug where priv is referenced
before it's actually allocated and then is tried to write to for the
is_1000basex and is_fiber variables in the case of at8031, writing on
the wrong address.
Fix this by correctly setting priv local variable only after
at803x_probe is called and actually allocates priv in the phydev struct. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Fix command flush on cable pull
System crash due to command failed to flush back to SCSI layer.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
PGD 0 P4D 0
Oops: 0000 [#1] SMP NOPTI
CPU: 27 PID: 793455 Comm: kworker/u130:6 Kdump: loaded Tainted: G OE --------- - - 4.18.0-372.9.1.el8.x86_64 #1
Hardware name: HPE ProLiant DL360 Gen10/ProLiant DL360 Gen10, BIOS U32 09/03/2021
Workqueue: nvme-wq nvme_fc_connect_ctrl_work [nvme_fc]
RIP: 0010:__wake_up_common+0x4c/0x190
Code: 24 10 4d 85 c9 74 0a 41 f6 01 04 0f 85 9d 00 00 00 48 8b 43 08 48 83 c3 08 4c 8d 48 e8 49 8d 41 18 48 39 c3 0f 84 f0 00 00 00 <49> 8b 41 18 89 54 24 08 31 ed 4c 8d 70 e8 45 8b 29 41 f6 c5 04 75
RSP: 0018:ffff95f3e0cb7cd0 EFLAGS: 00010086
RAX: 0000000000000000 RBX: ffff8b08d3b26328 RCX: 0000000000000000
RDX: 0000000000000001 RSI: 0000000000000003 RDI: ffff8b08d3b26320
RBP: 0000000000000001 R08: 0000000000000000 R09: ffffffffffffffe8
R10: 0000000000000000 R11: ffff95f3e0cb7a60 R12: ffff95f3e0cb7d20
R13: 0000000000000003 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff8b2fdf6c0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000002f1e410002 CR4: 00000000007706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
__wake_up_common_lock+0x7c/0xc0
qla_nvme_ls_req+0x355/0x4c0 [qla2xxx]
qla2xxx [0000:12:00.1]-f084:3: qlt_free_session_done: se_sess 0000000000000000 / sess ffff8ae1407ca000 from port 21:32:00:02:ac:07:ee:b8 loop_id 0x02 s_id 01:02:00 logout 1 keep 0 els_logo 0
? __nvme_fc_send_ls_req+0x260/0x380 [nvme_fc]
qla2xxx [0000:12:00.1]-207d:3: FCPort 21:32:00:02:ac:07:ee:b8 state transitioned from ONLINE to LOST - portid=010200.
? nvme_fc_send_ls_req.constprop.42+0x1a/0x45 [nvme_fc]
qla2xxx [0000:12:00.1]-2109:3: qla2x00_schedule_rport_del 21320002ac07eeb8. rport ffff8ae598122000 roles 1
? nvme_fc_connect_ctrl_work.cold.63+0x1e3/0xa7d [nvme_fc]
qla2xxx [0000:12:00.1]-f084:3: qlt_free_session_done: se_sess 0000000000000000 / sess ffff8ae14801e000 from port 21:32:01:02:ad:f7:ee:b8 loop_id 0x04 s_id 01:02:01 logout 1 keep 0 els_logo 0
? __switch_to+0x10c/0x450
? process_one_work+0x1a7/0x360
qla2xxx [0000:12:00.1]-207d:3: FCPort 21:32:01:02:ad:f7:ee:b8 state transitioned from ONLINE to LOST - portid=010201.
? worker_thread+0x1ce/0x390
? create_worker+0x1a0/0x1a0
qla2xxx [0000:12:00.1]-2109:3: qla2x00_schedule_rport_del 21320102adf7eeb8. rport ffff8ae3b2312800 roles 70
? kthread+0x10a/0x120
qla2xxx [0000:12:00.1]-2112:3: qla_nvme_unregister_remote_port: unregister remoteport on ffff8ae14801e000 21320102adf7eeb8
? set_kthread_struct+0x40/0x40
qla2xxx [0000:12:00.1]-2110:3: remoteport_delete of ffff8ae14801e000 21320102adf7eeb8 completed.
? ret_from_fork+0x1f/0x40
qla2xxx [0000:12:00.1]-f086:3: qlt_free_session_done: waiting for sess ffff8ae14801e000 logout
The system was under memory stress where driver was not able to allocate an
SRB to carry out error recovery of cable pull. The failure to flush causes
upper layer to start modifying scsi_cmnd. When the system frees up some
memory, the subsequent cable pull trigger another command flush. At this
point the driver access a null pointer when attempting to DMA unmap the
SGL.
Add a check to make sure commands are flush back on session tear down to
prevent the null pointer access. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_set_pipapo: do not free live element
Pablo reports a crash with large batches of elements with a
back-to-back add/remove pattern. Quoting Pablo:
add_elem("00000000") timeout 100 ms
...
add_elem("0000000X") timeout 100 ms
del_elem("0000000X") <---------------- delete one that was just added
...
add_elem("00005000") timeout 100 ms
1) nft_pipapo_remove() removes element 0000000X
Then, KASAN shows a splat.
Looking at the remove function there is a chance that we will drop a
rule that maps to a non-deactivated element.
Removal happens in two steps, first we do a lookup for key k and return the
to-be-removed element and mark it as inactive in the next generation.
Then, in a second step, the element gets removed from the set/map.
The _remove function does not work correctly if we have more than one
element that share the same key.
This can happen if we insert an element into a set when the set already
holds an element with same key, but the element mapping to the existing
key has timed out or is not active in the next generation.
In such case its possible that removal will unmap the wrong element.
If this happens, we will leak the non-deactivated element, it becomes
unreachable.
The element that got deactivated (and will be freed later) will
remain reachable in the set data structure, this can result in
a crash when such an element is retrieved during lookup (stale
pointer).
Add a check that the fully matching key does in fact map to the element
that we have marked as inactive in the deactivation step.
If not, we need to continue searching.
Add a bug/warn trap at the end of the function as well, the remove
function must not ever be called with an invisible/unreachable/non-existent
element.
v2: avoid uneeded temporary variable (Stefano) |
| In the Linux kernel, the following vulnerability has been resolved:
perf: RISCV: Fix panic on pmu overflow handler
(1 << idx) of int is not desired when setting bits in unsigned long
overflowed_ctrs, use BIT() instead. This panic happens when running
'perf record -e branches' on sophgo sg2042.
[ 273.311852] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000098
[ 273.320851] Oops [#1]
[ 273.323179] Modules linked in:
[ 273.326303] CPU: 0 PID: 1475 Comm: perf Not tainted 6.6.0-rc3+ #9
[ 273.332521] Hardware name: Sophgo Mango (DT)
[ 273.336878] epc : riscv_pmu_ctr_get_width_mask+0x8/0x62
[ 273.342291] ra : pmu_sbi_ovf_handler+0x2e0/0x34e
[ 273.347091] epc : ffffffff80aecd98 ra : ffffffff80aee056 sp : fffffff6e36928b0
[ 273.354454] gp : ffffffff821f82d0 tp : ffffffd90c353200 t0 : 0000002ade4f9978
[ 273.361815] t1 : 0000000000504d55 t2 : ffffffff8016cd8c s0 : fffffff6e3692a70
[ 273.369180] s1 : 0000000000000020 a0 : 0000000000000000 a1 : 00001a8e81800000
[ 273.376540] a2 : 0000003c00070198 a3 : 0000003c00db75a4 a4 : 0000000000000015
[ 273.383901] a5 : ffffffd7ff8804b0 a6 : 0000000000000015 a7 : 000000000000002a
[ 273.391327] s2 : 000000000000ffff s3 : 0000000000000000 s4 : ffffffd7ff8803b0
[ 273.398773] s5 : 0000000000504d55 s6 : ffffffd905069800 s7 : ffffffff821fe210
[ 273.406139] s8 : 000000007fffffff s9 : ffffffd7ff8803b0 s10: ffffffd903f29098
[ 273.413660] s11: 0000000080000000 t3 : 0000000000000003 t4 : ffffffff8017a0ca
[ 273.421022] t5 : ffffffff8023cfc2 t6 : ffffffd9040780e8
[ 273.426437] status: 0000000200000100 badaddr: 0000000000000098 cause: 000000000000000d
[ 273.434512] [<ffffffff80aecd98>] riscv_pmu_ctr_get_width_mask+0x8/0x62
[ 273.441169] [<ffffffff80076bd8>] handle_percpu_devid_irq+0x98/0x1ee
[ 273.447562] [<ffffffff80071158>] generic_handle_domain_irq+0x28/0x36
[ 273.454151] [<ffffffff8047a99a>] riscv_intc_irq+0x36/0x4e
[ 273.459659] [<ffffffff80c944de>] handle_riscv_irq+0x4a/0x74
[ 273.465442] [<ffffffff80c94c48>] do_irq+0x62/0x92
[ 273.470360] Code: 0420 60a2 6402 5529 0141 8082 0013 0000 0013 0000 (6d5c) b783
[ 273.477921] ---[ end trace 0000000000000000 ]---
[ 273.482630] Kernel panic - not syncing: Fatal exception in interrupt |
