| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: change DMA direction while mapping reinjected packets
For fragmented packets, ath12k reassembles each fragment as a normal
packet and then reinjects it into HW ring. In this case, the DMA
direction should be DMA_TO_DEVICE, not DMA_FROM_DEVICE. Otherwise,
an invalid payload may be reinjected into the HW and
subsequently delivered to the host.
Given that arbitrary memory can be allocated to the skb buffer,
knowledge about the data contained in the reinjected buffer is lacking.
Consequently, there’s a risk of private information being leaked.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
mlxsw: spectrum_acl_erp: Fix object nesting warning
ACLs in Spectrum-2 and newer ASICs can reside in the algorithmic TCAM
(A-TCAM) or in the ordinary circuit TCAM (C-TCAM). The former can
contain more ACLs (i.e., tc filters), but the number of masks in each
region (i.e., tc chain) is limited.
In order to mitigate the effects of the above limitation, the device
allows filters to share a single mask if their masks only differ in up
to 8 consecutive bits. For example, dst_ip/25 can be represented using
dst_ip/24 with a delta of 1 bit. The C-TCAM does not have a limit on the
number of masks being used (and therefore does not support mask
aggregation), but can contain a limited number of filters.
The driver uses the "objagg" library to perform the mask aggregation by
passing it objects that consist of the filter's mask and whether the
filter is to be inserted into the A-TCAM or the C-TCAM since filters in
different TCAMs cannot share a mask.
The set of created objects is dependent on the insertion order of the
filters and is not necessarily optimal. Therefore, the driver will
periodically ask the library to compute a more optimal set ("hints") by
looking at all the existing objects.
When the library asks the driver whether two objects can be aggregated
the driver only compares the provided masks and ignores the A-TCAM /
C-TCAM indication. This is the right thing to do since the goal is to
move as many filters as possible to the A-TCAM. The driver also forbids
two identical masks from being aggregated since this can only happen if
one was intentionally put in the C-TCAM to avoid a conflict in the
A-TCAM.
The above can result in the following set of hints:
H1: {mask X, A-TCAM} -> H2: {mask Y, A-TCAM} // X is Y + delta
H3: {mask Y, C-TCAM} -> H4: {mask Z, A-TCAM} // Y is Z + delta
After getting the hints from the library the driver will start migrating
filters from one region to another while consulting the computed hints
and instructing the device to perform a lookup in both regions during
the transition.
Assuming a filter with mask X is being migrated into the A-TCAM in the
new region, the hints lookup will return H1. Since H2 is the parent of
H1, the library will try to find the object associated with it and
create it if necessary in which case another hints lookup (recursive)
will be performed. This hints lookup for {mask Y, A-TCAM} will either
return H2 or H3 since the driver passes the library an object comparison
function that ignores the A-TCAM / C-TCAM indication.
This can eventually lead to nested objects which are not supported by
the library [1].
Fix by removing the object comparison function from both the driver and
the library as the driver was the only user. That way the lookup will
only return exact matches.
I do not have a reliable reproducer that can reproduce the issue in a
timely manner, but before the fix the issue would reproduce in several
minutes and with the fix it does not reproduce in over an hour.
Note that the current usefulness of the hints is limited because they
include the C-TCAM indication and represent aggregation that cannot
actually happen. This will be addressed in net-next.
[1]
WARNING: CPU: 0 PID: 153 at lib/objagg.c:170 objagg_obj_parent_assign+0xb5/0xd0
Modules linked in:
CPU: 0 PID: 153 Comm: kworker/0:18 Not tainted 6.9.0-rc6-custom-g70fbc2c1c38b #42
Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:objagg_obj_parent_assign+0xb5/0xd0
[...]
Call Trace:
<TASK>
__objagg_obj_get+0x2bb/0x580
objagg_obj_get+0xe/0x80
mlxsw_sp_acl_erp_mask_get+0xb5/0xf0
mlxsw_sp_acl_atcam_entry_add+0xe8/0x3c0
mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0
mlxsw_sp_acl_tcam_vchunk_migrate_one+0x16b/0x270
mlxsw_sp_acl_tcam_vregion_rehash_work+0xbe/0x510
process_one_work+0x151/0x370 |
| In the Linux kernel, the following vulnerability has been resolved:
perf: Fix event leak upon exit
When a task is scheduled out, pending sigtrap deliveries are deferred
to the target task upon resume to userspace via task_work.
However failures while adding an event's callback to the task_work
engine are ignored. And since the last call for events exit happen
after task work is eventually closed, there is a small window during
which pending sigtrap can be queued though ignored, leaking the event
refcount addition such as in the following scenario:
TASK A
-----
do_exit()
exit_task_work(tsk);
<IRQ>
perf_event_overflow()
event->pending_sigtrap = pending_id;
irq_work_queue(&event->pending_irq);
</IRQ>
=========> PREEMPTION: TASK A -> TASK B
event_sched_out()
event->pending_sigtrap = 0;
atomic_long_inc_not_zero(&event->refcount)
// FAILS: task work has exited
task_work_add(&event->pending_task)
[...]
<IRQ WORK>
perf_pending_irq()
// early return: event->oncpu = -1
</IRQ WORK>
[...]
=========> TASK B -> TASK A
perf_event_exit_task(tsk)
perf_event_exit_event()
free_event()
WARN(atomic_long_cmpxchg(&event->refcount, 1, 0) != 1)
// leak event due to unexpected refcount == 2
As a result the event is never released while the task exits.
Fix this with appropriate task_work_add()'s error handling. |
| In the Linux kernel, the following vulnerability has been resolved:
perf: Fix event leak upon exec and file release
The perf pending task work is never waited upon the matching event
release. In the case of a child event, released via free_event()
directly, this can potentially result in a leaked event, such as in the
following scenario that doesn't even require a weak IRQ work
implementation to trigger:
schedule()
prepare_task_switch()
=======> <NMI>
perf_event_overflow()
event->pending_sigtrap = ...
irq_work_queue(&event->pending_irq)
<======= </NMI>
perf_event_task_sched_out()
event_sched_out()
event->pending_sigtrap = 0;
atomic_long_inc_not_zero(&event->refcount)
task_work_add(&event->pending_task)
finish_lock_switch()
=======> <IRQ>
perf_pending_irq()
//do nothing, rely on pending task work
<======= </IRQ>
begin_new_exec()
perf_event_exit_task()
perf_event_exit_event()
// If is child event
free_event()
WARN(atomic_long_cmpxchg(&event->refcount, 1, 0) != 1)
// event is leaked
Similar scenarios can also happen with perf_event_remove_on_exec() or
simply against concurrent perf_event_release().
Fix this with synchonizing against the possibly remaining pending task
work while freeing the event, just like is done with remaining pending
IRQ work. This means that the pending task callback neither need nor
should hold a reference to the event, preventing it from ever beeing
freed. |
| In the Linux kernel, the following vulnerability has been resolved:
lib: alloc_tag_module_unload must wait for pending kfree_rcu calls
Ben Greear reports following splat:
------------[ cut here ]------------
net/netfilter/nf_nat_core.c:1114 module nf_nat func:nf_nat_register_fn has 256 allocated at module unload
WARNING: CPU: 1 PID: 10421 at lib/alloc_tag.c:168 alloc_tag_module_unload+0x22b/0x3f0
Modules linked in: nf_nat(-) btrfs ufs qnx4 hfsplus hfs minix vfat msdos fat
...
Hardware name: Default string Default string/SKYBAY, BIOS 5.12 08/04/2020
RIP: 0010:alloc_tag_module_unload+0x22b/0x3f0
codetag_unload_module+0x19b/0x2a0
? codetag_load_module+0x80/0x80
nf_nat module exit calls kfree_rcu on those addresses, but the free
operation is likely still pending by the time alloc_tag checks for leaks.
Wait for outstanding kfree_rcu operations to complete before checking
resolves this warning.
Reproducer:
unshare -n iptables-nft -t nat -A PREROUTING -p tcp
grep nf_nat /proc/allocinfo # will list 4 allocations
rmmod nft_chain_nat
rmmod nf_nat # will WARN.
[akpm@linux-foundation.org: add comment] |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: replace BUG_ON() with error handling at update_ref_for_cow()
Instead of a BUG_ON() just return an error, log an error message and
abort the transaction in case we find an extent buffer belonging to the
relocation tree that doesn't have the full backref flag set. This is
unexpected and should never happen (save for bugs or a potential bad
memory). |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix double put of @cfile in smb2_rename_path()
If smb2_set_path_attr() is called with a valid @cfile and returned
-EINVAL, we need to call cifs_get_writable_path() again as the
reference of @cfile was already dropped by previous smb2_compound_op()
call. |
| Any project that parses untrusted Protocol Buffers data containing an arbitrary number of nested groups / series of SGROUP tags can corrupted by exceeding the stack limit i.e. StackOverflow. Parsing nested groups as unknown fields with DiscardUnknownFieldsParser or Java Protobuf Lite parser, or against Protobuf map fields, creates unbounded recursions that can be abused by an attacker. |
| In the Linux kernel, the following vulnerability has been resolved:
net: mctp: take ownership of skb in mctp_local_output
Currently, mctp_local_output only takes ownership of skb on success, and
we may leak an skb if mctp_local_output fails in specific states; the
skb ownership isn't transferred until the actual output routing occurs.
Instead, make mctp_local_output free the skb on all error paths up to
the route action, so it always consumes the passed skb. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring: Fix release of pinned pages when __io_uaddr_map fails
Looking at the error path of __io_uaddr_map, if we fail after pinning
the pages for any reasons, ret will be set to -EINVAL and the error
handler won't properly release the pinned pages.
I didn't manage to trigger it without forcing a failure, but it can
happen in real life when memory is heavily fragmented. |
| In the Linux kernel, the following vulnerability has been resolved:
iommufd: Fix out_fput in iommufd_fault_alloc()
As fput() calls the file->f_op->release op, where fault obj and ictx are
getting released, there is no need to release these two after fput() one
more time, which would result in imbalanced refcounts:
refcount_t: decrement hit 0; leaking memory.
WARNING: CPU: 48 PID: 2369 at lib/refcount.c:31 refcount_warn_saturate+0x60/0x230
Call trace:
refcount_warn_saturate+0x60/0x230 (P)
refcount_warn_saturate+0x60/0x230 (L)
iommufd_fault_fops_release+0x9c/0xe0 [iommufd]
...
VFS: Close: file count is 0 (f_op=iommufd_fops [iommufd])
WARNING: CPU: 48 PID: 2369 at fs/open.c:1507 filp_flush+0x3c/0xf0
Call trace:
filp_flush+0x3c/0xf0 (P)
filp_flush+0x3c/0xf0 (L)
__arm64_sys_close+0x34/0x98
...
imbalanced put on file reference count
WARNING: CPU: 48 PID: 2369 at fs/file.c:74 __file_ref_put+0x100/0x138
Call trace:
__file_ref_put+0x100/0x138 (P)
__file_ref_put+0x100/0x138 (L)
__fput_sync+0x4c/0xd0
Drop those two lines to fix the warnings above. |
| In the Linux kernel, the following vulnerability has been resolved:
net: tls, fix WARNIING in __sk_msg_free
A splice with MSG_SPLICE_PAGES will cause tls code to use the
tls_sw_sendmsg_splice path in the TLS sendmsg code to move the user
provided pages from the msg into the msg_pl. This will loop over the
msg until msg_pl is full, checked by sk_msg_full(msg_pl). The user
can also set the MORE flag to hint stack to delay sending until receiving
more pages and ideally a full buffer.
If the user adds more pages to the msg than can fit in the msg_pl
scatterlist (MAX_MSG_FRAGS) we should ignore the MORE flag and send
the buffer anyways.
What actually happens though is we abort the msg to msg_pl scatterlist
setup and then because we forget to set 'full record' indicating we
can no longer consume data without a send we fallthrough to the 'continue'
path which will check if msg_data_left(msg) has more bytes to send and
then attempts to fit them in the already full msg_pl. Then next
iteration of sender doing send will encounter a full msg_pl and throw
the warning in the syzbot report.
To fix simply check if we have a full_record in splice code path and
if not send the msg regardless of MORE flag. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: compress: fix reserve_cblocks counting error when out of space
When a file only needs one direct_node, performing the following
operations will cause the file to be unrepairable:
unisoc # ./f2fs_io compress test.apk
unisoc #df -h | grep dm-48
/dev/block/dm-48 112G 112G 1.2M 100% /data
unisoc # ./f2fs_io release_cblocks test.apk
924
unisoc # df -h | grep dm-48
/dev/block/dm-48 112G 112G 4.8M 100% /data
unisoc # dd if=/dev/random of=file4 bs=1M count=3
3145728 bytes (3.0 M) copied, 0.025 s, 120 M/s
unisoc # df -h | grep dm-48
/dev/block/dm-48 112G 112G 1.8M 100% /data
unisoc # ./f2fs_io reserve_cblocks test.apk
F2FS_IOC_RESERVE_COMPRESS_BLOCKS failed: No space left on device
adb reboot
unisoc # df -h | grep dm-48
/dev/block/dm-48 112G 112G 11M 100% /data
unisoc # ./f2fs_io reserve_cblocks test.apk
0
This is because the file has only one direct_node. After returning
to -ENOSPC, reserved_blocks += ret will not be executed. As a result,
the reserved_blocks at this time is still 0, which is not the real
number of reserved blocks. Therefore, fsck cannot be set to repair
the file.
After this patch, the fsck flag will be set to fix this problem.
unisoc # df -h | grep dm-48
/dev/block/dm-48 112G 112G 1.8M 100% /data
unisoc # ./f2fs_io reserve_cblocks test.apk
F2FS_IOC_RESERVE_COMPRESS_BLOCKS failed: No space left on device
adb reboot then fsck will be executed
unisoc # df -h | grep dm-48
/dev/block/dm-48 112G 112G 11M 100% /data
unisoc # ./f2fs_io reserve_cblocks test.apk
924 |
| In the Linux kernel, the following vulnerability has been resolved:
firewire: ohci: prevent leak of left-over IRQ on unbind
Commit 5a95f1ded28691e6 ("firewire: ohci: use devres for requested IRQ")
also removed the call to free_irq() in pci_remove(), leading to a
leftover irq of devm_request_irq() at pci_disable_msi() in pci_remove()
when unbinding the driver from the device
remove_proc_entry: removing non-empty directory 'irq/136', leaking at
least 'firewire_ohci'
Call Trace:
? remove_proc_entry+0x19c/0x1c0
? __warn+0x81/0x130
? remove_proc_entry+0x19c/0x1c0
? report_bug+0x171/0x1a0
? console_unlock+0x78/0x120
? handle_bug+0x3c/0x80
? exc_invalid_op+0x17/0x70
? asm_exc_invalid_op+0x1a/0x20
? remove_proc_entry+0x19c/0x1c0
unregister_irq_proc+0xf4/0x120
free_desc+0x3d/0xe0
? kfree+0x29f/0x2f0
irq_free_descs+0x47/0x70
msi_domain_free_locked.part.0+0x19d/0x1d0
msi_domain_free_irqs_all_locked+0x81/0xc0
pci_free_msi_irqs+0x12/0x40
pci_disable_msi+0x4c/0x60
pci_remove+0x9d/0xc0 [firewire_ohci
01b483699bebf9cb07a3d69df0aa2bee71db1b26]
pci_device_remove+0x37/0xa0
device_release_driver_internal+0x19f/0x200
unbind_store+0xa1/0xb0
remove irq with devm_free_irq() before pci_disable_msi()
also remove it in fail_msi: of pci_probe() as this would lead to
an identical leak |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: qgroup: fix quota root leak after quota disable failure
If during the quota disable we fail when cleaning the quota tree or when
deleting the root from the root tree, we jump to the 'out' label without
ever dropping the reference on the quota root, resulting in a leak of the
root since fs_info->quota_root is no longer pointing to the root (we have
set it to NULL just before those steps).
Fix this by always doing a btrfs_put_root() call under the 'out' label.
This is a problem that exists since qgroups were first added in 2012 by
commit bed92eae26cc ("Btrfs: qgroup implementation and prototypes"), but
back then we missed a kfree on the quota root and free_extent_buffer()
calls on its root and commit root nodes, since back then roots were not
yet reference counted. |
| ruby-saml provides security assertion markup language (SAML) single sign-on (SSO) for Ruby. Prior to versions 1.12.4 and 1.18.0, ruby-saml is susceptible to remote Denial of Service (DoS) with compressed SAML responses. ruby-saml uses zlib to decompress SAML responses in case they're compressed. It is possible to bypass the message size check with a compressed assertion since the message size is checked before inflation and not after. This issue may lead to remote Denial of Service (DoS). Versions 1.12.4 and 1.18.0 fix the issue. |
| gpac v2.2.1 (fixed in v2.4.0) was discovered to contain a memory leak via the gfio_blob variable in the gf_fileio_from_blob function. |
| Discourse is an open source platform for community discussion. In affected versions the endpoint for generating inline oneboxes for URLs wasn't enforcing limits on the number of URLs that it accepted, allowing a malicious user to inflict denial of service on some parts of the app. This vulnerability is only exploitable by authenticated users. This issue has been patched in the latest stable, beta and tests-passed versions of Discourse. Users are advised to upgrade. Users unable to upgrade should turn off the `enable inline onebox on all domains` site setting and remove all entries from the `allowed inline onebox domains` site setting. |
| Discourse is an open-source discussion platform. Prior to version 3.4.4 of the `stable` branch, version 3.5.0.beta5 of the `beta` branch, and version 3.5.0.beta6-dev of the `tests-passed` branch, sending a malicious URL in a PM to a bot user can cause a reduced the availability of a Discourse instance. This issue is patched in version 3.4.4 of the `stable` branch, version 3.5.0.beta5 of the `beta` branch, and version 3.5.0.beta6-dev of the `tests-passed` branch. No known workarounds are available. |
| Discourse is an open source platform for community discussion. A user can create a post with many replies, and then attempt to fetch them all at once. This can potentially reduce the availability of a Discourse instance. This problem has been patched in the latest version of Discourse. All users area are advised to upgrade. There are no known workarounds for this vulnerability. |
