| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: ucsi: Fix NULL pointer deref in ucsi_connector_change()
When ucsi_init() fails, ucsi->connector is NULL, yet in case of
ucsi_acpi we may still get events which cause the ucs_acpi code to call
ucsi_connector_change(), which then derefs the NULL ucsi->connector
pointer.
Fix this by not setting ucsi->ntfy inside ucsi_init() until ucsi_init()
has succeeded, so that ucsi_connector_change() ignores the events
because UCSI_ENABLE_NTFY_CONNECTOR_CHANGE is not set in the ntfy mask. |
| In the Linux kernel, the following vulnerability has been resolved:
fscrypt: destroy keyring after security_sb_delete()
fscrypt_destroy_keyring() must be called after all potentially-encrypted
inodes were evicted; otherwise it cannot safely destroy the keyring.
Since inodes that are in-use by the Landlock LSM don't get evicted until
security_sb_delete(), this means that fscrypt_destroy_keyring() must be
called *after* security_sb_delete().
This fixes a WARN_ON followed by a NULL dereference, only possible if
Landlock was being used on encrypted files. |
| In the Linux kernel, the following vulnerability has been resolved:
dm stats: check for and propagate alloc_percpu failure
Check alloc_precpu()'s return value and return an error from
dm_stats_init() if it fails. Update alloc_dev() to fail if
dm_stats_init() does.
Otherwise, a NULL pointer dereference will occur in dm_stats_cleanup()
even if dm-stats isn't being actively used. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: zoned: clone zoned device info when cloning a device
When cloning a btrfs_device, we're not cloning the associated
btrfs_zoned_device_info structure of the device in case of a zoned
filesystem.
Later on this leads to a NULL pointer dereference when accessing the
device's zone_info for instance when setting a zone as active.
This was uncovered by fstests' testcase btrfs/161. |
| In the Linux kernel, the following vulnerability has been resolved:
book3s64/radix : Align section vmemmap start address to PAGE_SIZE
A vmemmap altmap is a device-provided region used to provide
backing storage for struct pages. For each namespace, the altmap
should belong to that same namespace. If the namespaces are
created unaligned, there is a chance that the section vmemmap
start address could also be unaligned. If the section vmemmap
start address is unaligned, the altmap page allocated from the
current namespace might be used by the previous namespace also.
During the free operation, since the altmap is shared between two
namespaces, the previous namespace may detect that the page does
not belong to its altmap and incorrectly assume that the page is a
normal page. It then attempts to free the normal page, which leads
to a kernel crash.
Kernel attempted to read user page (18) - exploit attempt? (uid: 0)
BUG: Kernel NULL pointer dereference on read at 0x00000018
Faulting instruction address: 0xc000000000530c7c
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
CPU: 32 PID: 2104 Comm: ndctl Kdump: loaded Tainted: G W
NIP: c000000000530c7c LR: c000000000530e00 CTR: 0000000000007ffe
REGS: c000000015e57040 TRAP: 0300 Tainted: G W
MSR: 800000000280b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 84482404
CFAR: c000000000530dfc DAR: 0000000000000018 DSISR: 40000000 IRQMASK: 0
GPR00: c000000000530e00 c000000015e572e0 c000000002c5cb00 c00c000101008040
GPR04: 0000000000000000 0000000000000007 0000000000000001 000000000000001f
GPR08: 0000000000000005 0000000000000000 0000000000000018 0000000000002000
GPR12: c0000000001d2fb0 c0000060de6b0080 0000000000000000 c0000060dbf90020
GPR16: c00c000101008000 0000000000000001 0000000000000000 c000000125b20f00
GPR20: 0000000000000001 0000000000000000 ffffffffffffffff c00c000101007fff
GPR24: 0000000000000001 0000000000000000 0000000000000000 0000000000000000
GPR28: 0000000004040201 0000000000000001 0000000000000000 c00c000101008040
NIP [c000000000530c7c] get_pfnblock_flags_mask+0x7c/0xd0
LR [c000000000530e00] free_unref_page_prepare+0x130/0x4f0
Call Trace:
free_unref_page+0x50/0x1e0
free_reserved_page+0x40/0x68
free_vmemmap_pages+0x98/0xe0
remove_pte_table+0x164/0x1e8
remove_pmd_table+0x204/0x2c8
remove_pud_table+0x1c4/0x288
remove_pagetable+0x1c8/0x310
vmemmap_free+0x24/0x50
section_deactivate+0x28c/0x2a0
__remove_pages+0x84/0x110
arch_remove_memory+0x38/0x60
memunmap_pages+0x18c/0x3d0
devm_action_release+0x30/0x50
release_nodes+0x68/0x140
devres_release_group+0x100/0x190
dax_pmem_compat_release+0x44/0x80 [dax_pmem_compat]
device_for_each_child+0x8c/0x100
[dax_pmem_compat_remove+0x2c/0x50 [dax_pmem_compat]
nvdimm_bus_remove+0x78/0x140 [libnvdimm]
device_remove+0x70/0xd0
Another issue is that if there is no altmap, a PMD-sized vmemmap
page will be allocated from RAM, regardless of the alignment of
the section start address. If the section start address is not
aligned to the PMD size, a VM_BUG_ON will be triggered when
setting the PMD-sized page to page table.
In this patch, we are aligning the section vmemmap start address
to PAGE_SIZE. After alignment, the start address will not be
part of the current namespace, and a normal page will be allocated
for the vmemmap mapping of the current section. For the remaining
sections, altmaps will be allocated. During the free operation,
the normal page will be correctly freed.
In the same way, a PMD_SIZE vmemmap page will be allocated only if
the section start address is PMD_SIZE-aligned; otherwise, it will
fall back to a PAGE-sized vmemmap allocation.
Without this patch
==================
NS1 start NS2 start
_________________________________________________________
| NS1 | NS2 |
---------------------------------------------------------
| Altmap| Altmap | .....|Altmap| Altmap | ...........
| NS1 | NS1
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
ata: libata-transport: fix error handling in ata_tdev_add()
In ata_tdev_add(), the return value of transport_add_device() is
not checked. As a result, it causes null-ptr-deref while removing
the module, because transport_remove_device() is called to remove
the device that was not added.
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000d0
CPU: 13 PID: 13603 Comm: rmmod Kdump: loaded Tainted: G W 6.1.0-rc3+ #36
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : device_del+0x48/0x3a0
lr : device_del+0x44/0x3a0
Call trace:
device_del+0x48/0x3a0
attribute_container_class_device_del+0x28/0x40
transport_remove_classdev+0x60/0x7c
attribute_container_device_trigger+0x118/0x120
transport_remove_device+0x20/0x30
ata_tdev_delete+0x24/0x50 [libata]
ata_tlink_delete+0x40/0xa0 [libata]
ata_tport_delete+0x2c/0x60 [libata]
ata_port_detach+0x148/0x1b0 [libata]
ata_pci_remove_one+0x50/0x80 [libata]
ahci_remove_one+0x4c/0x8c [ahci]
Fix this by checking and handling return value of transport_add_device()
in ata_tdev_add(). In the error path, device_del() is called to delete
the device which was added earlier in this function, and ata_tdev_free()
is called to free ata_dev. |
| In the Linux kernel, the following vulnerability has been resolved:
ata: libata-transport: fix error handling in ata_tlink_add()
In ata_tlink_add(), the return value of transport_add_device() is
not checked. As a result, it causes null-ptr-deref while removing
the module, because transport_remove_device() is called to remove
the device that was not added.
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000d0
CPU: 33 PID: 13850 Comm: rmmod Kdump: loaded Tainted: G W 6.1.0-rc3+ #12
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : device_del+0x48/0x39c
lr : device_del+0x44/0x39c
Call trace:
device_del+0x48/0x39c
attribute_container_class_device_del+0x28/0x40
transport_remove_classdev+0x60/0x7c
attribute_container_device_trigger+0x118/0x120
transport_remove_device+0x20/0x30
ata_tlink_delete+0x88/0xb0 [libata]
ata_tport_delete+0x2c/0x60 [libata]
ata_port_detach+0x148/0x1b0 [libata]
ata_pci_remove_one+0x50/0x80 [libata]
ahci_remove_one+0x4c/0x8c [ahci]
Fix this by checking and handling return value of transport_add_device()
in ata_tlink_add(). |
| In the Linux kernel, the following vulnerability has been resolved:
ata: libata-transport: fix error handling in ata_tport_add()
In ata_tport_add(), the return value of transport_add_device() is
not checked. As a result, it causes null-ptr-deref while removing
the module, because transport_remove_device() is called to remove
the device that was not added.
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000d0
CPU: 12 PID: 13605 Comm: rmmod Kdump: loaded Tainted: G W 6.1.0-rc3+ #8
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : device_del+0x48/0x39c
lr : device_del+0x44/0x39c
Call trace:
device_del+0x48/0x39c
attribute_container_class_device_del+0x28/0x40
transport_remove_classdev+0x60/0x7c
attribute_container_device_trigger+0x118/0x120
transport_remove_device+0x20/0x30
ata_tport_delete+0x34/0x60 [libata]
ata_port_detach+0x148/0x1b0 [libata]
ata_pci_remove_one+0x50/0x80 [libata]
ahci_remove_one+0x4c/0x8c [ahci]
Fix this by checking and handling return value of transport_add_device()
in ata_tport_add(). |
| In the Linux kernel, the following vulnerability has been resolved:
drm: Fix potential null-ptr-deref in drm_vblank_destroy_worker()
drm_vblank_init() call drmm_add_action_or_reset() with
drm_vblank_init_release() as action. If __drmm_add_action() failed, will
directly call drm_vblank_init_release() with the vblank whose worker is
NULL. As the resule, a null-ptr-deref will happen in
kthread_destroy_worker(). Add the NULL check before calling
drm_vblank_destroy_worker().
BUG: null-ptr-deref
KASAN: null-ptr-deref in range [0x0000000000000068-0x000000000000006f]
CPU: 5 PID: 961 Comm: modprobe Not tainted 6.0.0-11331-gd465bff130bf-dirty
RIP: 0010:kthread_destroy_worker+0x25/0xb0
Call Trace:
<TASK>
drm_vblank_init_release+0x124/0x220 [drm]
? drm_crtc_vblank_restore+0x8b0/0x8b0 [drm]
__drmm_add_action_or_reset+0x41/0x50 [drm]
drm_vblank_init+0x282/0x310 [drm]
vkms_init+0x35f/0x1000 [vkms]
? 0xffffffffc4508000
? lock_is_held_type+0xd7/0x130
? __kmem_cache_alloc_node+0x1c2/0x2b0
? lock_is_held_type+0xd7/0x130
? 0xffffffffc4508000
do_one_initcall+0xd0/0x4f0
...
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0 |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: devicetree: fix null pointer dereferencing in pinctrl_dt_to_map
Here is the BUG report by KASAN about null pointer dereference:
BUG: KASAN: null-ptr-deref in strcmp+0x2e/0x50
Read of size 1 at addr 0000000000000000 by task python3/2640
Call Trace:
strcmp
__of_find_property
of_find_property
pinctrl_dt_to_map
kasprintf() would return NULL pointer when kmalloc() fail to allocate.
So directly return ENOMEM, if kasprintf() return NULL pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: xsk: disable txq irq before flushing hw
ice_qp_dis() intends to stop a given queue pair that is a target of xsk
pool attach/detach. One of the steps is to disable interrupts on these
queues. It currently is broken in a way that txq irq is turned off
*after* HW flush which in turn takes no effect.
ice_qp_dis():
-> ice_qvec_dis_irq()
--> disable rxq irq
--> flush hw
-> ice_vsi_stop_tx_ring()
-->disable txq irq
Below splat can be triggered by following steps:
- start xdpsock WITHOUT loading xdp prog
- run xdp_rxq_info with XDP_TX action on this interface
- start traffic
- terminate xdpsock
[ 256.312485] BUG: kernel NULL pointer dereference, address: 0000000000000018
[ 256.319560] #PF: supervisor read access in kernel mode
[ 256.324775] #PF: error_code(0x0000) - not-present page
[ 256.329994] PGD 0 P4D 0
[ 256.332574] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 256.337006] CPU: 3 PID: 32 Comm: ksoftirqd/3 Tainted: G OE 6.2.0-rc5+ #51
[ 256.345218] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019
[ 256.355807] RIP: 0010:ice_clean_rx_irq_zc+0x9c/0x7d0 [ice]
[ 256.361423] Code: b7 8f 8a 00 00 00 66 39 ca 0f 84 f1 04 00 00 49 8b 47 40 4c 8b 24 d0 41 0f b7 45 04 66 25 ff 3f 66 89 04 24 0f 84 85 02 00 00 <49> 8b 44 24 18 0f b7 14 24 48 05 00 01 00 00 49 89 04 24 49 89 44
[ 256.380463] RSP: 0018:ffffc900088bfd20 EFLAGS: 00010206
[ 256.385765] RAX: 000000000000003c RBX: 0000000000000035 RCX: 000000000000067f
[ 256.393012] RDX: 0000000000000775 RSI: 0000000000000000 RDI: ffff8881deb3ac80
[ 256.400256] RBP: 000000000000003c R08: ffff889847982710 R09: 0000000000010000
[ 256.407500] R10: ffffffff82c060c0 R11: 0000000000000004 R12: 0000000000000000
[ 256.414746] R13: ffff88811165eea0 R14: ffffc9000d255000 R15: ffff888119b37600
[ 256.421990] FS: 0000000000000000(0000) GS:ffff8897e0cc0000(0000) knlGS:0000000000000000
[ 256.430207] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 256.436036] CR2: 0000000000000018 CR3: 0000000005c0a006 CR4: 00000000007706e0
[ 256.443283] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 256.450527] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 256.457770] PKRU: 55555554
[ 256.460529] Call Trace:
[ 256.463015] <TASK>
[ 256.465157] ? ice_xmit_zc+0x6e/0x150 [ice]
[ 256.469437] ice_napi_poll+0x46d/0x680 [ice]
[ 256.473815] ? _raw_spin_unlock_irqrestore+0x1b/0x40
[ 256.478863] __napi_poll+0x29/0x160
[ 256.482409] net_rx_action+0x136/0x260
[ 256.486222] __do_softirq+0xe8/0x2e5
[ 256.489853] ? smpboot_thread_fn+0x2c/0x270
[ 256.494108] run_ksoftirqd+0x2a/0x50
[ 256.497747] smpboot_thread_fn+0x1c1/0x270
[ 256.501907] ? __pfx_smpboot_thread_fn+0x10/0x10
[ 256.506594] kthread+0xea/0x120
[ 256.509785] ? __pfx_kthread+0x10/0x10
[ 256.513597] ret_from_fork+0x29/0x50
[ 256.517238] </TASK>
In fact, irqs were not disabled and napi managed to be scheduled and run
while xsk_pool pointer was still valid, but SW ring of xdp_buff pointers
was already freed.
To fix this, call ice_qvec_dis_irq() after ice_vsi_stop_tx_ring(). Also
while at it, remove redundant ice_clean_rx_ring() call - this is handled
in ice_qp_clean_rings(). |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Fix cleanup null-ptr deref on encap lock
During module is unloaded while a peer tc flow is still offloaded,
first the peer uplink rep profile is changed to a nic profile, and so
neigh encap lock is destroyed. Next during unload, the VF reps netdevs
are unregistered which causes the original non-peer tc flow to be deleted,
which deletes the peer flow. The peer flow deletion detaches the encap
entry and try to take the already destroyed encap lock, causing the
below trace.
Fix this by clearing peer flows during tc eswitch cleanup
(mlx5e_tc_esw_cleanup()).
Relevant trace:
[ 4316.837128] BUG: kernel NULL pointer dereference, address: 00000000000001d8
[ 4316.842239] RIP: 0010:__mutex_lock+0xb5/0xc40
[ 4316.851897] Call Trace:
[ 4316.852481] <TASK>
[ 4316.857214] mlx5e_rep_neigh_entry_release+0x93/0x790 [mlx5_core]
[ 4316.858258] mlx5e_rep_encap_entry_detach+0xa7/0xf0 [mlx5_core]
[ 4316.859134] mlx5e_encap_dealloc+0xa3/0xf0 [mlx5_core]
[ 4316.859867] clean_encap_dests.part.0+0x5c/0xe0 [mlx5_core]
[ 4316.860605] mlx5e_tc_del_fdb_flow+0x32a/0x810 [mlx5_core]
[ 4316.862609] __mlx5e_tc_del_fdb_peer_flow+0x1a2/0x250 [mlx5_core]
[ 4316.863394] mlx5e_tc_del_flow+0x(/0x630 [mlx5_core]
[ 4316.864090] mlx5e_flow_put+0x5f/0x100 [mlx5_core]
[ 4316.864771] mlx5e_delete_flower+0x4de/0xa40 [mlx5_core]
[ 4316.865486] tc_setup_cb_reoffload+0x20/0x80
[ 4316.865905] fl_reoffload+0x47c/0x510 [cls_flower]
[ 4316.869181] tcf_block_playback_offloads+0x91/0x1d0
[ 4316.869649] tcf_block_unbind+0xe7/0x1b0
[ 4316.870049] tcf_block_offload_cmd.isra.0+0x1ee/0x270
[ 4316.879266] tcf_block_offload_unbind+0x61/0xa0
[ 4316.879711] __tcf_block_put+0xa4/0x310 |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: fix NULL sndbuf_desc in smc_cdc_tx_handler()
When performing a stress test on SMC-R by rmmod mlx5_ib driver
during the wrk/nginx test, we found that there is a probability
of triggering a panic while terminating all link groups.
This issue dues to the race between smc_smcr_terminate_all()
and smc_buf_create().
smc_smcr_terminate_all
smc_buf_create
/* init */
conn->sndbuf_desc = NULL;
...
__smc_lgr_terminate
smc_conn_kill
smc_close_abort
smc_cdc_get_slot_and_msg_send
__softirqentry_text_start
smc_wr_tx_process_cqe
smc_cdc_tx_handler
READ(conn->sndbuf_desc->len);
/* panic dues to NULL sndbuf_desc */
conn->sndbuf_desc = xxx;
This patch tries to fix the issue by always to check the sndbuf_desc
before send any cdc msg, to make sure that no null pointer is
seen during cqe processing. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: nl80211: fix NULL-ptr deref in offchan check
If, e.g. in AP mode, the link was already created by userspace
but not activated yet, it has a chandef but the chandef isn't
valid and has no channel. Check for this and ignore this link. |
| In the Linux kernel, the following vulnerability has been resolved:
i40e: Fix kernel crash during reboot when adapter is in recovery mode
If the driver detects during probe that firmware is in recovery
mode then i40e_init_recovery_mode() is called and the rest of
probe function is skipped including pci_set_drvdata(). Subsequent
i40e_shutdown() called during shutdown/reboot dereferences NULL
pointer as pci_get_drvdata() returns NULL.
To fix call pci_set_drvdata() also during entering to recovery mode.
Reproducer:
1) Lets have i40e NIC with firmware in recovery mode
2) Run reboot
Result:
[ 139.084698] i40e: Intel(R) Ethernet Connection XL710 Network Driver
[ 139.090959] i40e: Copyright (c) 2013 - 2019 Intel Corporation.
[ 139.108438] i40e 0000:02:00.0: Firmware recovery mode detected. Limiting functionality.
[ 139.116439] i40e 0000:02:00.0: Refer to the Intel(R) Ethernet Adapters and Devices User Guide for details on firmware recovery mode.
[ 139.129499] i40e 0000:02:00.0: fw 8.3.64775 api 1.13 nvm 8.30 0x8000b78d 1.3106.0 [8086:1583] [15d9:084a]
[ 139.215932] i40e 0000:02:00.0 enp2s0f0: renamed from eth0
[ 139.223292] i40e 0000:02:00.1: Firmware recovery mode detected. Limiting functionality.
[ 139.231292] i40e 0000:02:00.1: Refer to the Intel(R) Ethernet Adapters and Devices User Guide for details on firmware recovery mode.
[ 139.244406] i40e 0000:02:00.1: fw 8.3.64775 api 1.13 nvm 8.30 0x8000b78d 1.3106.0 [8086:1583] [15d9:084a]
[ 139.329209] i40e 0000:02:00.1 enp2s0f1: renamed from eth0
...
[ 156.311376] BUG: kernel NULL pointer dereference, address: 00000000000006c2
[ 156.318330] #PF: supervisor write access in kernel mode
[ 156.323546] #PF: error_code(0x0002) - not-present page
[ 156.328679] PGD 0 P4D 0
[ 156.331210] Oops: 0002 [#1] PREEMPT SMP NOPTI
[ 156.335567] CPU: 26 PID: 15119 Comm: reboot Tainted: G E 6.2.0+ #1
[ 156.343126] Hardware name: Abacus electric, s.r.o. - servis@abacus.cz Super Server/H12SSW-iN, BIOS 2.4 04/13/2022
[ 156.353369] RIP: 0010:i40e_shutdown+0x15/0x130 [i40e]
[ 156.358430] Code: c1 fc ff ff 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 0f 1e fa 0f 1f 44 00 00 55 48 89 fd 53 48 8b 9f 48 01 00 00 <f0> 80 8b c2 06 00 00 04 f0 80 8b c0 06 00 00 08 48 8d bb 08 08 00
[ 156.377168] RSP: 0018:ffffb223c8447d90 EFLAGS: 00010282
[ 156.382384] RAX: ffffffffc073ee70 RBX: 0000000000000000 RCX: 0000000000000001
[ 156.389510] RDX: 0000000080000001 RSI: 0000000000000246 RDI: ffff95db49988000
[ 156.396634] RBP: ffff95db49988000 R08: ffffffffffffffff R09: ffffffff8bd17d40
[ 156.403759] R10: 0000000000000001 R11: ffffffff8a5e3d28 R12: ffff95db49988000
[ 156.410882] R13: ffffffff89a6fe17 R14: ffff95db49988150 R15: 0000000000000000
[ 156.418007] FS: 00007fe7c0cc3980(0000) GS:ffff95ea8ee80000(0000) knlGS:0000000000000000
[ 156.426083] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 156.431819] CR2: 00000000000006c2 CR3: 00000003092fc005 CR4: 0000000000770ee0
[ 156.438944] PKRU: 55555554
[ 156.441647] Call Trace:
[ 156.444096] <TASK>
[ 156.446199] pci_device_shutdown+0x38/0x60
[ 156.450297] device_shutdown+0x163/0x210
[ 156.454215] kernel_restart+0x12/0x70
[ 156.457872] __do_sys_reboot+0x1ab/0x230
[ 156.461789] ? vfs_writev+0xa6/0x1a0
[ 156.465362] ? __pfx_file_free_rcu+0x10/0x10
[ 156.469635] ? __call_rcu_common.constprop.85+0x109/0x5a0
[ 156.475034] do_syscall_64+0x3e/0x90
[ 156.478611] entry_SYSCALL_64_after_hwframe+0x72/0xdc
[ 156.483658] RIP: 0033:0x7fe7bff37ab7 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: mpt3sas: Fix NULL pointer access in mpt3sas_transport_port_add()
Port is allocated by sas_port_alloc_num() and rphy is allocated by either
sas_end_device_alloc() or sas_expander_alloc(), all of which may return
NULL. So we need to check the rphy to avoid possible NULL pointer access.
If sas_rphy_add() returned with failure, rphy is set to NULL. We would
access the rphy in the following lines which would also result NULL pointer
access. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: fdp: add null check of devm_kmalloc_array in fdp_nci_i2c_read_device_properties
devm_kmalloc_array may fails, *fw_vsc_cfg might be null and cause
out-of-bounds write in device_property_read_u8_array later. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: fix wrong kunmap when using LZMA on HIGHMEM platforms
As the call trace shown, the root cause is kunmap incorrect pages:
BUG: kernel NULL pointer dereference, address: 00000000
CPU: 1 PID: 40 Comm: kworker/u5:0 Not tainted 6.2.0-rc5 #4
Workqueue: erofs_worker z_erofs_decompressqueue_work
EIP: z_erofs_lzma_decompress+0x34b/0x8ac
z_erofs_decompress+0x12/0x14
z_erofs_decompress_queue+0x7e7/0xb1c
z_erofs_decompressqueue_work+0x32/0x60
process_one_work+0x24b/0x4d8
? process_one_work+0x1a4/0x4d8
worker_thread+0x14c/0x3fc
kthread+0xe6/0x10c
? rescuer_thread+0x358/0x358
? kthread_complete_and_exit+0x18/0x18
ret_from_fork+0x1c/0x28
---[ end trace 0000000000000000 ]---
The bug is trivial and should be fixed now. It has no impact on
!HIGHMEM platforms. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: consider that tail calls invalidate packet pointers
Tail-called programs could execute any of the helpers that invalidate
packet pointers. Hence, conservatively assume that each tail call
invalidates packet pointers.
Making the change in bpf_helper_changes_pkt_data() automatically makes
use of check_cfg() logic that computes 'changes_pkt_data' effect for
global sub-programs, such that the following program could be
rejected:
int tail_call(struct __sk_buff *sk)
{
bpf_tail_call_static(sk, &jmp_table, 0);
return 0;
}
SEC("tc")
int not_safe(struct __sk_buff *sk)
{
int *p = (void *)(long)sk->data;
... make p valid ...
tail_call(sk);
*p = 42; /* this is unsafe */
...
}
The tc_bpf2bpf.c:subprog_tc() needs change: mark it as a function that
can invalidate packet pointers. Otherwise, it can't be freplaced with
tailcall_freplace.c:entry_freplace() that does a tail call. |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: fix NULL pointer dereference in tipc_mon_reinit_self()
syzbot reported:
tipc: Node number set to 1055423674
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 3 UID: 0 PID: 6017 Comm: kworker/3:5 Not tainted 6.15.0-rc1-syzkaller-00246-g900241a5cc15 #0 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
Workqueue: events tipc_net_finalize_work
RIP: 0010:tipc_mon_reinit_self+0x11c/0x210 net/tipc/monitor.c:719
...
RSP: 0018:ffffc9000356fb68 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 000000003ee87cba
RDX: 0000000000000000 RSI: ffffffff8dbc56a7 RDI: ffff88804c2cc010
RBP: dffffc0000000000 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000007
R13: fffffbfff2111097 R14: ffff88804ead8000 R15: ffff88804ead9010
FS: 0000000000000000(0000) GS:ffff888097ab9000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000f720eb00 CR3: 000000000e182000 CR4: 0000000000352ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
tipc_net_finalize+0x10b/0x180 net/tipc/net.c:140
process_one_work+0x9cc/0x1b70 kernel/workqueue.c:3238
process_scheduled_works kernel/workqueue.c:3319 [inline]
worker_thread+0x6c8/0xf10 kernel/workqueue.c:3400
kthread+0x3c2/0x780 kernel/kthread.c:464
ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:153
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK>
...
RIP: 0010:tipc_mon_reinit_self+0x11c/0x210 net/tipc/monitor.c:719
...
RSP: 0018:ffffc9000356fb68 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 000000003ee87cba
RDX: 0000000000000000 RSI: ffffffff8dbc56a7 RDI: ffff88804c2cc010
RBP: dffffc0000000000 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000007
R13: fffffbfff2111097 R14: ffff88804ead8000 R15: ffff88804ead9010
FS: 0000000000000000(0000) GS:ffff888097ab9000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000f720eb00 CR3: 000000000e182000 CR4: 0000000000352ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
There is a racing condition between workqueue created when enabling
bearer and another thread created when disabling bearer right after
that as follow:
enabling_bearer | disabling_bearer
--------------- | ----------------
tipc_disc_timeout() |
{ | bearer_disable()
... | {
schedule_work(&tn->work); | tipc_mon_delete()
... | {
} | ...
| write_lock_bh(&mon->lock);
| mon->self = NULL;
| write_unlock_bh(&mon->lock);
| ...
| }
tipc_net_finalize_work() | }
{ |
... |
tipc_net_finalize() |
{ |
... |
tipc_mon_reinit_self() |
{ |
... |
write_lock_bh(&mon->lock); |
mon->self->addr = tipc_own_addr(net); |
write_unlock_bh(&mon->lock); |
...
---truncated--- |
