| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
firewire: core: fix race condition against transaction list
The list of transaction is enumerated without acquiring card lock when
processing AR response event. This causes a race condition bug when
processing AT request completion event concurrently.
This commit fixes the bug by put timer start for split transaction
expiration into the scope of lock. The value of jiffies in card structure
is referred before acquiring the lock. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_uart: fix null-ptr-deref in hci_uart_write_work
hci_uart_set_proto() sets HCI_UART_PROTO_INIT before calling
hci_uart_register_dev(), which calls proto->open() to initialize
hu->priv. However, if a TTY write wakeup occurs during this window,
hci_uart_tx_wakeup() may schedule write_work before hu->priv is
initialized, leading to a NULL pointer dereference in
hci_uart_write_work() when proto->dequeue() accesses hu->priv.
The race condition is:
CPU0 CPU1
---- ----
hci_uart_set_proto()
set_bit(HCI_UART_PROTO_INIT)
hci_uart_register_dev()
tty write wakeup
hci_uart_tty_wakeup()
hci_uart_tx_wakeup()
schedule_work(&hu->write_work)
proto->open(hu)
// initializes hu->priv
hci_uart_write_work()
hci_uart_dequeue()
proto->dequeue(hu)
// accesses hu->priv (NULL!)
Fix this by moving set_bit(HCI_UART_PROTO_INIT) after proto->open()
succeeds, ensuring hu->priv is initialized before any work can be
scheduled. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/sysfs-scheme: cleanup access_pattern subdirs on scheme dir setup failure
When a DAMOS-scheme DAMON sysfs directory setup fails after setup of
access_pattern/ directory, subdirectories of access_pattern/ directory are
not cleaned up. As a result, DAMON sysfs interface is nearly broken until
the system reboots, and the memory for the unremoved directory is leaked.
Cleanup the directories under such failures. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: MGMT: Fix memory leak in set_ssp_complete
Fix memory leak in set_ssp_complete() where mgmt_pending_cmd structures
are not freed after being removed from the pending list.
Commit 302a1f674c00 ("Bluetooth: MGMT: Fix possible UAFs") replaced
mgmt_pending_foreach() calls with individual command handling but missed
adding mgmt_pending_free() calls in both error and success paths of
set_ssp_complete(). Other completion functions like set_le_complete()
were fixed correctly in the same commit.
This causes a memory leak of the mgmt_pending_cmd structure and its
associated parameter data for each SSP command that completes.
Add the missing mgmt_pending_free(cmd) calls in both code paths to fix
the memory leak. Also fix the same issue in set_advertising_complete(). |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/sysfs: cleanup attrs subdirs on context dir setup failure
When a context DAMON sysfs directory setup is failed after setup of attrs/
directory, subdirectories of attrs/ directory are not cleaned up. As a
result, DAMON sysfs interface is nearly broken until the system reboots,
and the memory for the unremoved directory is leaked.
Cleanup the directories under such failures. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: zlib: fix the folio leak on S390 hardware acceleration
[BUG]
After commit aa60fe12b4f4 ("btrfs: zlib: refactor S390x HW acceleration
buffer preparation"), we no longer release the folio of the page cache
of folio returned by btrfs_compress_filemap_get_folio() for S390
hardware acceleration path.
[CAUSE]
Before that commit, we call kumap_local() and folio_put() after handling
each folio.
Although the timing is not ideal (it release previous folio at the
beginning of the loop, and rely on some extra cleanup out of the loop),
it at least handles the folio release correctly.
Meanwhile the refactored code is easier to read, it lacks the call to
release the filemap folio.
[FIX]
Add the missing folio_put() for copy_data_into_buffer(). |
| In the Linux kernel, the following vulnerability has been resolved:
net: fix segmentation of forwarding fraglist GRO
This patch enhances GSO segment handling by properly checking
the SKB_GSO_DODGY flag for frag_list GSO packets, addressing
low throughput issues observed when a station accesses IPv4
servers via hotspots with an IPv6-only upstream interface.
Specifically, it fixes a bug in GSO segmentation when forwarding
GRO packets containing a frag_list. The function skb_segment_list
cannot correctly process GRO skbs that have been converted by XLAT,
since XLAT only translates the header of the head skb. Consequently,
skbs in the frag_list may remain untranslated, resulting in protocol
inconsistencies and reduced throughput.
To address this, the patch explicitly sets the SKB_GSO_DODGY flag
for GSO packets in XLAT's IPv4/IPv6 protocol translation helpers
(bpf_skb_proto_4_to_6 and bpf_skb_proto_6_to_4). This marks GSO
packets as potentially modified after protocol translation. As a
result, GSO segmentation will avoid using skb_segment_list and
instead falls back to skb_segment for packets with the SKB_GSO_DODGY
flag. This ensures that only safe and fully translated frag_list
packets are processed by skb_segment_list, resolving protocol
inconsistencies and improving throughput when forwarding GRO packets
converted by XLAT. |
| In the Linux kernel, the following vulnerability has been resolved:
flex_proportions: make fprop_new_period() hardirq safe
Bernd has reported a lockdep splat from flexible proportions code that is
essentially complaining about the following race:
<timer fires>
run_timer_softirq - we are in softirq context
call_timer_fn
writeout_period
fprop_new_period
write_seqcount_begin(&p->sequence);
<hardirq is raised>
...
blk_mq_end_request()
blk_update_request()
ext4_end_bio()
folio_end_writeback()
__wb_writeout_add()
__fprop_add_percpu_max()
if (unlikely(max_frac < FPROP_FRAC_BASE)) {
fprop_fraction_percpu()
seq = read_seqcount_begin(&p->sequence);
- sees odd sequence so loops indefinitely
Note that a deadlock like this is only possible if the bdi has configured
maximum fraction of writeout throughput which is very rare in general but
frequent for example for FUSE bdis. To fix this problem we have to make
sure write section of the sequence counter is irqsafe. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: send: check for inline extents in range_is_hole_in_parent()
Before accessing the disk_bytenr field of a file extent item we need
to check if we are dealing with an inline extent.
This is because for inline extents their data starts at the offset of
the disk_bytenr field. So accessing the disk_bytenr
means we are accessing inline data or in case the inline data is less
than 8 bytes we can actually cause an invalid
memory access if this inline extent item is the first item in the leaf
or access metadata from other items. |
| In the Linux kernel, the following vulnerability has been resolved:
can: gs_usb: gs_usb_receive_bulk_callback(): fix error message
Sinc commit 79a6d1bfe114 ("can: gs_usb: gs_usb_receive_bulk_callback():
unanchor URL on usb_submit_urb() error") a failing resubmit URB will print
an info message.
In the case of a short read where netdev has not yet been assigned,
initialize as NULL to avoid dereferencing an undefined value. Also report
the error value of the failed resubmit. |
| In the Linux kernel, the following vulnerability has been resolved:
octeon_ep: Fix memory leak in octep_device_setup()
In octep_device_setup(), if octep_ctrl_net_init() fails, the function
returns directly without unmapping the mapped resources and freeing the
allocated configuration memory.
Fix this by jumping to the unsupported_dev label, which performs the
necessary cleanup. This aligns with the error handling logic of other
paths in this function.
Compile tested only. Issue found using a prototype static analysis tool
and code review. |
| In the Linux kernel, the following vulnerability has been resolved:
of: unittest: Fix memory leak in unittest_data_add()
In unittest_data_add(), if of_resolve_phandles() fails, the allocated
unittest_data is not freed, leading to a memory leak.
Fix this by using scope-based cleanup helper __free(kfree) for automatic
resource cleanup. This ensures unittest_data is automatically freed when
it goes out of scope in error paths.
For the success path, use retain_and_null_ptr() to transfer ownership
of the memory to the device tree and prevent double freeing. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/sva: invalidate stale IOTLB entries for kernel address space
Introduce a new IOMMU interface to flush IOTLB paging cache entries for
the CPU kernel address space. This interface is invoked from the x86
architecture code that manages combined user and kernel page tables,
specifically before any kernel page table page is freed and reused.
This addresses the main issue with vfree() which is a common occurrence
and can be triggered by unprivileged users. While this resolves the
primary problem, it doesn't address some extremely rare case related to
memory unplug of memory that was present as reserved memory at boot, which
cannot be triggered by unprivileged users. The discussion can be found at
the link below.
Enable SVA on x86 architecture since the IOMMU can now receive
notification to flush the paging cache before freeing the CPU kernel page
table pages. |
| In the Linux kernel, the following vulnerability has been resolved:
rocker: fix memory leak in rocker_world_port_post_fini()
In rocker_world_port_pre_init(), rocker_port->wpriv is allocated with
kzalloc(wops->port_priv_size, GFP_KERNEL). However, in
rocker_world_port_post_fini(), the memory is only freed when
wops->port_post_fini callback is set:
if (!wops->port_post_fini)
return;
wops->port_post_fini(rocker_port);
kfree(rocker_port->wpriv);
Since rocker_ofdpa_ops does not implement port_post_fini callback
(it is NULL), the wpriv memory allocated for each port is never freed
when ports are removed. This leads to a memory leak of
sizeof(struct ofdpa_port) bytes per port on every device removal.
Fix this by always calling kfree(rocker_port->wpriv) regardless of
whether the port_post_fini callback exists. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: fix dma_free_coherent() pointer
dma_alloc_coherent() allocates a DMA mapped buffer and stores the
addresses in XXX_unaligned fields. Those should be reused when freeing
the buffer rather than the aligned addresses. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/io-wq: check IO_WQ_BIT_EXIT inside work run loop
Currently this is checked before running the pending work. Normally this
is quite fine, as work items either end up blocking (which will create a
new worker for other items), or they complete fairly quickly. But syzbot
reports an issue where io-wq takes seemingly forever to exit, and with a
bit of debugging, this turns out to be because it queues a bunch of big
(2GB - 4096b) reads with a /dev/msr* file. Since this file type doesn't
support ->read_iter(), loop_rw_iter() ends up handling them. Each read
returns 16MB of data read, which takes 20 (!!) seconds. With a bunch of
these pending, processing the whole chain can take a long time. Easily
longer than the syzbot uninterruptible sleep timeout of 140 seconds.
This then triggers a complaint off the io-wq exit path:
INFO: task syz.4.135:6326 blocked for more than 143 seconds.
Not tainted syzkaller #0
Blocked by coredump.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:syz.4.135 state:D stack:26824 pid:6326 tgid:6324 ppid:5957 task_flags:0x400548 flags:0x00080000
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5256 [inline]
__schedule+0x1139/0x6150 kernel/sched/core.c:6863
__schedule_loop kernel/sched/core.c:6945 [inline]
schedule+0xe7/0x3a0 kernel/sched/core.c:6960
schedule_timeout+0x257/0x290 kernel/time/sleep_timeout.c:75
do_wait_for_common kernel/sched/completion.c:100 [inline]
__wait_for_common+0x2fc/0x4e0 kernel/sched/completion.c:121
io_wq_exit_workers io_uring/io-wq.c:1328 [inline]
io_wq_put_and_exit+0x271/0x8a0 io_uring/io-wq.c:1356
io_uring_clean_tctx+0x10d/0x190 io_uring/tctx.c:203
io_uring_cancel_generic+0x69c/0x9a0 io_uring/cancel.c:651
io_uring_files_cancel include/linux/io_uring.h:19 [inline]
do_exit+0x2ce/0x2bd0 kernel/exit.c:911
do_group_exit+0xd3/0x2a0 kernel/exit.c:1112
get_signal+0x2671/0x26d0 kernel/signal.c:3034
arch_do_signal_or_restart+0x8f/0x7e0 arch/x86/kernel/signal.c:337
__exit_to_user_mode_loop kernel/entry/common.c:41 [inline]
exit_to_user_mode_loop+0x8c/0x540 kernel/entry/common.c:75
__exit_to_user_mode_prepare include/linux/irq-entry-common.h:226 [inline]
syscall_exit_to_user_mode_prepare include/linux/irq-entry-common.h:256 [inline]
syscall_exit_to_user_mode_work include/linux/entry-common.h:159 [inline]
syscall_exit_to_user_mode include/linux/entry-common.h:194 [inline]
do_syscall_64+0x4ee/0xf80 arch/x86/entry/syscall_64.c:100
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fa02738f749
RSP: 002b:00007fa0281ae0e8 EFLAGS: 00000246 ORIG_RAX: 00000000000000ca
RAX: fffffffffffffe00 RBX: 00007fa0275e6098 RCX: 00007fa02738f749
RDX: 0000000000000000 RSI: 0000000000000080 RDI: 00007fa0275e6098
RBP: 00007fa0275e6090 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fa0275e6128 R14: 00007fff14e4fcb0 R15: 00007fff14e4fd98
There's really nothing wrong here, outside of processing these reads
will take a LONG time. However, we can speed up the exit by checking the
IO_WQ_BIT_EXIT inside the io_worker_handle_work() loop, as syzbot will
exit the ring after queueing up all of these reads. Then once the first
item is processed, io-wq will simply cancel the rest. That should avoid
syzbot running into this complaint again. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: Fix NULL pointer dereference in ice_vsi_set_napi_queues
Add NULL pointer checks in ice_vsi_set_napi_queues() to prevent crashes
during resume from suspend when rings[q_idx]->q_vector is NULL.
Tested adaptor:
60:00.0 Ethernet controller [0200]: Intel Corporation Ethernet Controller E810-XXV for SFP [8086:159b] (rev 02)
Subsystem: Intel Corporation Ethernet Network Adapter E810-XXV-2 [8086:4003]
SR-IOV state: both disabled and enabled can reproduce this issue.
kernel version: v6.18
Reproduce steps:
Boot up and execute suspend like systemctl suspend or rtcwake.
Log:
<1>[ 231.443607] BUG: kernel NULL pointer dereference, address: 0000000000000040
<1>[ 231.444052] #PF: supervisor read access in kernel mode
<1>[ 231.444484] #PF: error_code(0x0000) - not-present page
<6>[ 231.444913] PGD 0 P4D 0
<4>[ 231.445342] Oops: Oops: 0000 [#1] SMP NOPTI
<4>[ 231.446635] RIP: 0010:netif_queue_set_napi+0xa/0x170
<4>[ 231.447067] Code: 31 f6 31 ff c3 cc cc cc cc 0f 1f 80 00 00 00 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 48 85 c9 74 0b <48> 83 79 30 00 0f 84 39 01 00 00 55 41 89 d1 49 89 f8 89 f2 48 89
<4>[ 231.447513] RSP: 0018:ffffcc780fc078c0 EFLAGS: 00010202
<4>[ 231.447961] RAX: ffff8b848ca30400 RBX: ffff8b848caf2028 RCX: 0000000000000010
<4>[ 231.448443] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff8b848dbd4000
<4>[ 231.448896] RBP: ffffcc780fc078e8 R08: 0000000000000000 R09: 0000000000000000
<4>[ 231.449345] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000001
<4>[ 231.449817] R13: ffff8b848dbd4000 R14: ffff8b84833390c8 R15: 0000000000000000
<4>[ 231.450265] FS: 00007c7b29e9d740(0000) GS:ffff8b8c068e2000(0000) knlGS:0000000000000000
<4>[ 231.450715] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4>[ 231.451179] CR2: 0000000000000040 CR3: 000000030626f004 CR4: 0000000000f72ef0
<4>[ 231.451629] PKRU: 55555554
<4>[ 231.452076] Call Trace:
<4>[ 231.452549] <TASK>
<4>[ 231.452996] ? ice_vsi_set_napi_queues+0x4d/0x110 [ice]
<4>[ 231.453482] ice_resume+0xfd/0x220 [ice]
<4>[ 231.453977] ? __pfx_pci_pm_resume+0x10/0x10
<4>[ 231.454425] pci_pm_resume+0x8c/0x140
<4>[ 231.454872] ? __pfx_pci_pm_resume+0x10/0x10
<4>[ 231.455347] dpm_run_callback+0x5f/0x160
<4>[ 231.455796] ? dpm_wait_for_superior+0x107/0x170
<4>[ 231.456244] device_resume+0x177/0x270
<4>[ 231.456708] dpm_resume+0x209/0x2f0
<4>[ 231.457151] dpm_resume_end+0x15/0x30
<4>[ 231.457596] suspend_devices_and_enter+0x1da/0x2b0
<4>[ 231.458054] enter_state+0x10e/0x570
Add defensive checks for both the ring pointer and its q_vector
before dereferencing, allowing the system to resume successfully even when
q_vectors are unmapped. |
| In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix early read unlock of page with EOF in middle
The read result collection for buffered reads seems to run ahead of the
completion of subrequests under some circumstances, as can be seen in the
following log snippet:
9p_client_res: client 18446612686390831168 response P9_TREAD tag 0 err 0
...
netfs_sreq: R=00001b55[1] DOWN TERM f=192 s=0 5fb2/5fb2 s=5 e=0
...
netfs_collect_folio: R=00001b55 ix=00004 r=4000-5000 t=4000/5fb2
netfs_folio: i=157f3 ix=00004-00004 read-done
netfs_folio: i=157f3 ix=00004-00004 read-unlock
netfs_collect_folio: R=00001b55 ix=00005 r=5000-5fb2 t=5000/5fb2
netfs_folio: i=157f3 ix=00005-00005 read-done
netfs_folio: i=157f3 ix=00005-00005 read-unlock
...
netfs_collect_stream: R=00001b55[0:] cto=5fb2 frn=ffffffff
netfs_collect_state: R=00001b55 col=5fb2 cln=6000 n=c
netfs_collect_stream: R=00001b55[0:] cto=5fb2 frn=ffffffff
netfs_collect_state: R=00001b55 col=5fb2 cln=6000 n=8
...
netfs_sreq: R=00001b55[2] ZERO SUBMT f=000 s=5fb2 0/4e s=0 e=0
netfs_sreq: R=00001b55[2] ZERO TERM f=102 s=5fb2 4e/4e s=5 e=0
The 'cto=5fb2' indicates the collected file pos we've collected results to
so far - but we still have 0x4e more bytes to go - so we shouldn't have
collected folio ix=00005 yet. The 'ZERO' subreq that clears the tail
happens after we unlock the folio, allowing the application to see the
uncleared tail through mmap.
The problem is that netfs_read_unlock_folios() will unlock a folio in which
the amount of read results collected hits EOF position - but the ZERO
subreq lies beyond that and so happens after.
Fix this by changing the end check to always be the end of the folio and
never the end of the file.
In the future, I should look at clearing to the end of the folio here rather
than adding a ZERO subreq to do this. On the other hand, the ZERO subreq can
run in parallel with an async READ subreq. Further, the ZERO subreq may still
be necessary to, say, handle extents in a ceph file that don't have any
backing store and are thus implicitly all zeros.
This can be reproduced by creating a file, the size of which doesn't align
to a page boundary, e.g. 24998 (0x5fb2) bytes and then doing something
like:
xfs_io -c "mmap -r 0 0x6000" -c "madvise -d 0 0x6000" \
-c "mread -v 0 0x6000" /xfstest.test/x
The last 0x4e bytes should all be 00, but if the tail hasn't been cleared
yet, you may see rubbish there. This can be reproduced with kafs by
modifying the kernel to disable the call to netfs_read_subreq_progress()
and to stop afs_issue_read() from doing the async call for NETFS_READAHEAD.
Reproduction can be made easier by inserting an mdelay(100) in
netfs_issue_read() for the ZERO-subreq case.
AFS and CIFS are normally unlikely to show this as they dispatch READ ops
asynchronously, which allows the ZERO-subreq to finish first. 9P's READ op is
completely synchronous, so the ZERO-subreq will always happen after. It isn't
seen all the time, though, because the collection may be done in a worker
thread. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/bridge: synopsys: dw-dp: fix error paths of dw_dp_bind
Fix several issues in dw_dp_bind() error handling:
1. Missing return after drm_bridge_attach() failure - the function
continued execution instead of returning an error.
2. Resource leak: drm_dp_aux_register() is not a devm function, so
drm_dp_aux_unregister() must be called on all error paths after
aux registration succeeds. This affects errors from:
- drm_bridge_attach()
- phy_init()
- devm_add_action_or_reset()
- platform_get_irq()
- devm_request_threaded_irq()
3. Bug fix: platform_get_irq() returns the IRQ number or a negative
error code, but the error path was returning ERR_PTR(ret) instead
of ERR_PTR(dp->irq).
Use a goto label for cleanup to ensure consistent error handling. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix iloc.bh leak in ext4_xattr_inode_update_ref
The error branch for ext4_xattr_inode_update_ref forget to release the
refcount for iloc.bh. Find this when review code. |
