| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: bridge: fix use-after-free due to MST port state bypass
syzbot reported[1] a use-after-free when deleting an expired fdb. It is
due to a race condition between learning still happening and a port being
deleted, after all its fdbs have been flushed. The port's state has been
toggled to disabled so no learning should happen at that time, but if we
have MST enabled, it will bypass the port's state, that together with VLAN
filtering disabled can lead to fdb learning at a time when it shouldn't
happen while the port is being deleted. VLAN filtering must be disabled
because we flush the port VLANs when it's being deleted which will stop
learning. This fix adds a check for the port's vlan group which is
initialized to NULL when the port is getting deleted, that avoids the port
state bypass. When MST is enabled there would be a minimal new overhead
in the fast-path because the port's vlan group pointer is cache-hot.
[1] https://syzkaller.appspot.com/bug?extid=dd280197f0f7ab3917be |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: fix crash while sending Action Frames in standalone AP Mode
Currently, whenever there is a need to transmit an Action frame,
the brcmfmac driver always uses the P2P vif to send the "actframe" IOVAR to
firmware. The P2P interfaces were available when wpa_supplicant is managing
the wlan interface.
However, the P2P interfaces are not created/initialized when only hostapd
is managing the wlan interface. And if hostapd receives an ANQP Query REQ
Action frame even from an un-associated STA, the brcmfmac driver tries
to use an uninitialized P2P vif pointer for sending the IOVAR to firmware.
This NULL pointer dereferencing triggers a driver crash.
[ 1417.074538] Unable to handle kernel NULL pointer dereference at virtual
address 0000000000000000
[...]
[ 1417.075188] Hardware name: Raspberry Pi 4 Model B Rev 1.5 (DT)
[...]
[ 1417.075653] Call trace:
[ 1417.075662] brcmf_p2p_send_action_frame+0x23c/0xc58 [brcmfmac]
[ 1417.075738] brcmf_cfg80211_mgmt_tx+0x304/0x5c0 [brcmfmac]
[ 1417.075810] cfg80211_mlme_mgmt_tx+0x1b0/0x428 [cfg80211]
[ 1417.076067] nl80211_tx_mgmt+0x238/0x388 [cfg80211]
[ 1417.076281] genl_family_rcv_msg_doit+0xe0/0x158
[ 1417.076302] genl_rcv_msg+0x220/0x2a0
[ 1417.076317] netlink_rcv_skb+0x68/0x140
[ 1417.076330] genl_rcv+0x40/0x60
[ 1417.076343] netlink_unicast+0x330/0x3b8
[ 1417.076357] netlink_sendmsg+0x19c/0x3f8
[ 1417.076370] __sock_sendmsg+0x64/0xc0
[ 1417.076391] ____sys_sendmsg+0x268/0x2a0
[ 1417.076408] ___sys_sendmsg+0xb8/0x118
[ 1417.076427] __sys_sendmsg+0x90/0xf8
[ 1417.076445] __arm64_sys_sendmsg+0x2c/0x40
[ 1417.076465] invoke_syscall+0x50/0x120
[ 1417.076486] el0_svc_common.constprop.0+0x48/0xf0
[ 1417.076506] do_el0_svc+0x24/0x38
[ 1417.076525] el0_svc+0x30/0x100
[ 1417.076548] el0t_64_sync_handler+0x100/0x130
[ 1417.076569] el0t_64_sync+0x190/0x198
[ 1417.076589] Code: f9401e80 aa1603e2 f9403be1 5280e483 (f9400000)
Fix this, by always using the vif corresponding to the wdev on which the
Action frame Transmission request was initiated by the userspace. This way,
even if P2P vif is not available, the IOVAR is sent to firmware on AP vif
and the ANQP Query RESP Action frame is transmitted without crashing the
driver.
Move init_completion() for "send_af_done" from brcmf_p2p_create_p2pdev()
to brcmf_p2p_attach(). Because the former function would not get executed
when only hostapd is managing wlan interface, and it is not safe to do
reinit_completion() later in brcmf_p2p_tx_action_frame(), without any prior
init_completion().
And in the brcmf_p2p_tx_action_frame() function, the condition check for
P2P Presence response frame is not needed, since the wpa_supplicant is
properly sending the P2P Presense Response frame on the P2P-GO vif instead
of the P2P-Device vif.
[Cc stable] |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix potential cfid UAF in smb2_query_info_compound
When smb2_query_info_compound() retries, a previously allocated cfid may
have been freed in the first attempt.
Because cfid wasn't reset on replay, later cleanup could act on a stale
pointer, leading to a potential use-after-free.
Reinitialize cfid to NULL under the replay label.
Example trace (trimmed):
refcount_t: underflow; use-after-free.
WARNING: CPU: 1 PID: 11224 at ../lib/refcount.c:28 refcount_warn_saturate+0x9c/0x110
[...]
RIP: 0010:refcount_warn_saturate+0x9c/0x110
[...]
Call Trace:
<TASK>
smb2_query_info_compound+0x29c/0x5c0 [cifs f90b72658819bd21c94769b6a652029a07a7172f]
? step_into+0x10d/0x690
? __legitimize_path+0x28/0x60
smb2_queryfs+0x6a/0xf0 [cifs f90b72658819bd21c94769b6a652029a07a7172f]
smb311_queryfs+0x12d/0x140 [cifs f90b72658819bd21c94769b6a652029a07a7172f]
? kmem_cache_alloc+0x18a/0x340
? getname_flags+0x46/0x1e0
cifs_statfs+0x9f/0x2b0 [cifs f90b72658819bd21c94769b6a652029a07a7172f]
statfs_by_dentry+0x67/0x90
vfs_statfs+0x16/0xd0
user_statfs+0x54/0xa0
__do_sys_statfs+0x20/0x50
do_syscall_64+0x58/0x80 |
| In the Linux kernel, the following vulnerability has been resolved:
regmap: slimbus: fix bus_context pointer in regmap init calls
Commit 4e65bda8273c ("ASoC: wcd934x: fix error handling in
wcd934x_codec_parse_data()") revealed the problem in the slimbus regmap.
That commit breaks audio playback, for instance, on sdm845 Thundercomm
Dragonboard 845c board:
Unable to handle kernel paging request at virtual address ffff8000847cbad4
...
CPU: 5 UID: 0 PID: 776 Comm: aplay Not tainted 6.18.0-rc1-00028-g7ea30958b305 #11 PREEMPT
Hardware name: Thundercomm Dragonboard 845c (DT)
...
Call trace:
slim_xfer_msg+0x24/0x1ac [slimbus] (P)
slim_read+0x48/0x74 [slimbus]
regmap_slimbus_read+0x18/0x24 [regmap_slimbus]
_regmap_raw_read+0xe8/0x174
_regmap_bus_read+0x44/0x80
_regmap_read+0x60/0xd8
_regmap_update_bits+0xf4/0x140
_regmap_select_page+0xa8/0x124
_regmap_raw_write_impl+0x3b8/0x65c
_regmap_bus_raw_write+0x60/0x80
_regmap_write+0x58/0xc0
regmap_write+0x4c/0x80
wcd934x_hw_params+0x494/0x8b8 [snd_soc_wcd934x]
snd_soc_dai_hw_params+0x3c/0x7c [snd_soc_core]
__soc_pcm_hw_params+0x22c/0x634 [snd_soc_core]
dpcm_be_dai_hw_params+0x1d4/0x38c [snd_soc_core]
dpcm_fe_dai_hw_params+0x9c/0x17c [snd_soc_core]
snd_pcm_hw_params+0x124/0x464 [snd_pcm]
snd_pcm_common_ioctl+0x110c/0x1820 [snd_pcm]
snd_pcm_ioctl+0x34/0x4c [snd_pcm]
__arm64_sys_ioctl+0xac/0x104
invoke_syscall+0x48/0x104
el0_svc_common.constprop.0+0x40/0xe0
do_el0_svc+0x1c/0x28
el0_svc+0x34/0xec
el0t_64_sync_handler+0xa0/0xf0
el0t_64_sync+0x198/0x19c
The __devm_regmap_init_slimbus() started to be used instead of
__regmap_init_slimbus() after the commit mentioned above and turns out
the incorrect bus_context pointer (3rd argument) was used in
__devm_regmap_init_slimbus(). It should be just "slimbus" (which is equal
to &slimbus->dev). Correct it. The wcd934x codec seems to be the only or
the first user of devm_regmap_init_slimbus() but we should fix it till
the point where __devm_regmap_init_slimbus() was introduced therefore
two "Fixes" tags.
While at this, also correct the same argument in __regmap_init_slimbus(). |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: Define actions for the new time_deleg FATTR4 attributes
NFSv4 clients won't send legitimate GETATTR requests for these new
attributes because they are intended to be used only with CB_GETATTR
and SETATTR. But NFSD has to do something besides crashing if it
ever sees a GETATTR request that queries these attributes.
RFC 8881 Section 18.7.3 states:
> The server MUST return a value for each attribute that the client
> requests if the attribute is supported by the server for the
> target file system. If the server does not support a particular
> attribute on the target file system, then it MUST NOT return the
> attribute value and MUST NOT set the attribute bit in the result
> bitmap. The server MUST return an error if it supports an
> attribute on the target but cannot obtain its value. In that case,
> no attribute values will be returned.
Further, RFC 9754 Section 5 states:
> These new attributes are invalid to be used with GETATTR, VERIFY,
> and NVERIFY, and they can only be used with CB_GETATTR and SETATTR
> by a client holding an appropriate delegation.
Thus there does not appear to be a specific server response mandated
by specification. Taking the guidance that querying these attributes
via GETATTR is "invalid", NFSD will return nfserr_inval, failing the
request entirely. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/mediatek: Fix device use-after-free on unbind
A recent change fixed device reference leaks when looking up drm
platform device driver data during bind() but failed to remove a partial
fix which had been added by commit 80805b62ea5b ("drm/mediatek: Fix
kobject put for component sub-drivers").
This results in a reference imbalance on component bind() failures and
on unbind() which could lead to a user-after-free.
Make sure to only drop the references after retrieving the driver data
by effectively reverting the previous partial fix.
Note that holding a reference to a device does not prevent its driver
data from going away so there is no point in keeping the reference. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: fix race in hci_cmd_sync_dequeue_once
hci_cmd_sync_dequeue_once() does lookup and then cancel
the entry under two separate lock sections. Meanwhile,
hci_cmd_sync_work() can also delete the same entry,
leading to double list_del() and "UAF".
Fix this by holding cmd_sync_work_lock across both
lookup and cancel, so that the entry cannot be removed
concurrently. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Sync pending IRQ work before freeing ring buffer
Fix a race where irq_work can be queued in bpf_ringbuf_commit()
but the ring buffer is freed before the work executes.
In the syzbot reproducer, a BPF program attached to sched_switch
triggers bpf_ringbuf_commit(), queuing an irq_work. If the ring buffer
is freed before this work executes, the irq_work thread may accesses
freed memory.
Calling `irq_work_sync(&rb->work)` ensures that all pending irq_work
complete before freeing the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: Fix crash in nfsd4_read_release()
When tracing is enabled, the trace_nfsd_read_done trace point
crashes during the pynfs read.testNoFh test. |
| NVIDIA Triton Inference Server for Linux and Windows contains a vulnerability where an attacker could cause a stack overflow by sending extra-large payloads. A successful exploit of this vulnerability might lead to denial of service. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPI: video: Fix use-after-free in acpi_video_switch_brightness()
The switch_brightness_work delayed work accesses device->brightness
and device->backlight, freed by acpi_video_dev_unregister_backlight()
during device removal.
If the work executes after acpi_video_bus_unregister_backlight()
frees these resources, it causes a use-after-free when
acpi_video_switch_brightness() dereferences device->brightness or
device->backlight.
Fix this by calling cancel_delayed_work_sync() for each device's
switch_brightness_work in acpi_video_bus_remove_notify_handler()
after removing the notify handler that queues the work. This ensures
the work completes before the memory is freed.
[ rjw: Changelog edit ] |
| In the Linux kernel, the following vulnerability has been resolved:
net: macb: fix unregister_netdev call order in macb_remove()
When removing a macb device, the driver calls phy_exit() before
unregister_netdev(). This leads to a WARN from kernfs:
------------[ cut here ]------------
kernfs: can not remove 'attached_dev', no directory
WARNING: CPU: 1 PID: 27146 at fs/kernfs/dir.c:1683
Call trace:
kernfs_remove_by_name_ns+0xd8/0xf0
sysfs_remove_link+0x24/0x58
phy_detach+0x5c/0x168
phy_disconnect+0x4c/0x70
phylink_disconnect_phy+0x6c/0xc0 [phylink]
macb_close+0x6c/0x170 [macb]
...
macb_remove+0x60/0x168 [macb]
platform_remove+0x5c/0x80
...
The warning happens because the PHY is being exited while the netdev
is still registered. The correct order is to unregister the netdev
before shutting down the PHY and cleaning up the MDIO bus.
Fix this by moving unregister_netdev() ahead of phy_exit() in
macb_remove(). |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: reject duplicate device on updates
A chain/flowtable update with duplicated devices in the same batch is
possible. Unfortunately, netdev event path only removes the first
device that is found, leaving unregistered the hook of the duplicated
device.
Check if a duplicated device exists in the transaction batch, bail out
with EEXIST in such case.
WARNING is hit when unregistering the hook:
[49042.221275] WARNING: CPU: 4 PID: 8425 at net/netfilter/core.c:340 nf_hook_entry_head+0xaa/0x150
[49042.221375] CPU: 4 UID: 0 PID: 8425 Comm: nft Tainted: G S 6.16.0+ #170 PREEMPT(full)
[...]
[49042.221382] RIP: 0010:nf_hook_entry_head+0xaa/0x150 |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: fix double free in 'hci_discovery_filter_clear()'
Function 'hci_discovery_filter_clear()' frees 'uuids' array and then
sets it to NULL. There is a tiny chance of the following race:
'hci_cmd_sync_work()'
'update_passive_scan_sync()'
'hci_update_passive_scan_sync()'
'hci_discovery_filter_clear()'
kfree(uuids);
<-------------------------preempted-------------------------------->
'start_service_discovery()'
'hci_discovery_filter_clear()'
kfree(uuids); // DOUBLE FREE
<-------------------------preempted-------------------------------->
uuids = NULL;
To fix it let's add locking around 'kfree()' call and NULL pointer
assignment. Otherwise the following backtrace fires:
[ ] ------------[ cut here ]------------
[ ] kernel BUG at mm/slub.c:547!
[ ] Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP
[ ] CPU: 3 UID: 0 PID: 246 Comm: bluetoothd Tainted: G O 6.12.19-kernel #1
[ ] Tainted: [O]=OOT_MODULE
[ ] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ ] pc : __slab_free+0xf8/0x348
[ ] lr : __slab_free+0x48/0x348
...
[ ] Call trace:
[ ] __slab_free+0xf8/0x348
[ ] kfree+0x164/0x27c
[ ] start_service_discovery+0x1d0/0x2c0
[ ] hci_sock_sendmsg+0x518/0x924
[ ] __sock_sendmsg+0x54/0x60
[ ] sock_write_iter+0x98/0xf8
[ ] do_iter_readv_writev+0xe4/0x1c8
[ ] vfs_writev+0x128/0x2b0
[ ] do_writev+0xfc/0x118
[ ] __arm64_sys_writev+0x20/0x2c
[ ] invoke_syscall+0x68/0xf0
[ ] el0_svc_common.constprop.0+0x40/0xe0
[ ] do_el0_svc+0x1c/0x28
[ ] el0_svc+0x30/0xd0
[ ] el0t_64_sync_handler+0x100/0x12c
[ ] el0t_64_sync+0x194/0x198
[ ] Code: 8b0002e6 eb17031f 54fffbe1 d503201f (d4210000)
[ ] ---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix use-after-free in session logoff
The sess->user object can currently be in use by another thread, for
example if another connection has sent a session setup request to
bind to the session being free'd. The handler for that connection could
be in the smb2_sess_setup function which makes use of sess->user. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_set_pipapo: fix initial map fill
The initial buffer has to be inited to all-ones, but it must restrict
it to the size of the first field, not the total field size.
After each round in the map search step, the result and the fill map
are swapped, so if we have a set where f->bsize of the first element
is smaller than m->bsize_max, those one-bits are leaked into future
rounds result map.
This makes pipapo find an incorrect matching results for sets where
first field size is not the largest.
Followup patch adds a test case to nft_concat_range.sh selftest script.
Thanks to Stefano Brivio for pointing out that we need to zero out
the remainder explicitly, only correcting memset() argument isn't enough. |
| In the Linux kernel, the following vulnerability has been resolved:
pidfs: validate extensible ioctls
Validate extensible ioctls stricter than we do now. |
| In the Linux kernel, the following vulnerability has been resolved:
mount: handle NULL values in mnt_ns_release()
When calling in listmount() mnt_ns_release() may be passed a NULL
pointer. Handle that case gracefully. |
| In the Linux kernel, the following vulnerability has been resolved:
MIPS: SGI-IP27: Fix platform-device leak in bridge_platform_create()
In error case in bridge_platform_create after calling
platform_device_add()/platform_device_add_data()/
platform_device_add_resources(), release the failed
'pdev' or it will be leak, call platform_device_put()
to fix this problem.
Besides, 'pdev' is divided into 'pdev_wd' and 'pdev_bd',
use platform_device_unregister() to release sgi_w1
resources when xtalk-bridge registration fails. |
| In the Linux kernel, the following vulnerability has been resolved:
chardev: fix error handling in cdev_device_add()
While doing fault injection test, I got the following report:
------------[ cut here ]------------
kobject: '(null)' (0000000039956980): is not initialized, yet kobject_put() is being called.
WARNING: CPU: 3 PID: 6306 at kobject_put+0x23d/0x4e0
CPU: 3 PID: 6306 Comm: 283 Tainted: G W 6.1.0-rc2-00005-g307c1086d7c9 #1253
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
RIP: 0010:kobject_put+0x23d/0x4e0
Call Trace:
<TASK>
cdev_device_add+0x15e/0x1b0
__iio_device_register+0x13b4/0x1af0 [industrialio]
__devm_iio_device_register+0x22/0x90 [industrialio]
max517_probe+0x3d8/0x6b4 [max517]
i2c_device_probe+0xa81/0xc00
When device_add() is injected fault and returns error, if dev->devt is not set,
cdev_add() is not called, cdev_del() is not needed. Fix this by checking dev->devt
in error path. |
