| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/iommu: fix memory leak with using debugfs_lookup()
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once. |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: fix potential memory leaks in session setup
Make sure to free cifs_ses::auth_key.response before allocating it as
we might end up leaking memory in reconnect or mounting. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: spinand: fix memory leak of ECC engine conf
Memory allocated for the ECC engine conf is not released during spinand
cleanup. Below kmemleak trace is seen for this memory leak:
unreferenced object 0xffffff80064f00e0 (size 8):
comm "swapper/0", pid 1, jiffies 4294937458
hex dump (first 8 bytes):
00 00 00 00 00 00 00 00 ........
backtrace (crc 0):
kmemleak_alloc+0x30/0x40
__kmalloc_cache_noprof+0x208/0x3c0
spinand_ondie_ecc_init_ctx+0x114/0x200
nand_ecc_init_ctx+0x70/0xa8
nanddev_ecc_engine_init+0xec/0x27c
spinand_probe+0xa2c/0x1620
spi_mem_probe+0x130/0x21c
spi_probe+0xf0/0x170
really_probe+0x17c/0x6e8
__driver_probe_device+0x17c/0x21c
driver_probe_device+0x58/0x180
__device_attach_driver+0x15c/0x1f8
bus_for_each_drv+0xec/0x150
__device_attach+0x188/0x24c
device_initial_probe+0x10/0x20
bus_probe_device+0x11c/0x160
Fix the leak by calling nanddev_ecc_engine_cleanup() inside
spinand_cleanup(). |
| In the Linux kernel, the following vulnerability has been resolved:
ACPICA: fix acpi operand cache leak in dswstate.c
ACPICA commit 987a3b5cf7175916e2a4b6ea5b8e70f830dfe732
I found an ACPI cache leak in ACPI early termination and boot continuing case.
When early termination occurs due to malicious ACPI table, Linux kernel
terminates ACPI function and continues to boot process. While kernel terminates
ACPI function, kmem_cache_destroy() reports Acpi-Operand cache leak.
Boot log of ACPI operand cache leak is as follows:
>[ 0.585957] ACPI: Added _OSI(Module Device)
>[ 0.587218] ACPI: Added _OSI(Processor Device)
>[ 0.588530] ACPI: Added _OSI(3.0 _SCP Extensions)
>[ 0.589790] ACPI: Added _OSI(Processor Aggregator Device)
>[ 0.591534] ACPI Error: Illegal I/O port address/length above 64K: C806E00000004002/0x2 (20170303/hwvalid-155)
>[ 0.594351] ACPI Exception: AE_LIMIT, Unable to initialize fixed events (20170303/evevent-88)
>[ 0.597858] ACPI: Unable to start the ACPI Interpreter
>[ 0.599162] ACPI Error: Could not remove SCI handler (20170303/evmisc-281)
>[ 0.601836] kmem_cache_destroy Acpi-Operand: Slab cache still has objects
>[ 0.603556] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.12.0-rc5 #26
>[ 0.605159] Hardware name: innotek gmb_h virtual_box/virtual_box, BIOS virtual_box 12/01/2006
>[ 0.609177] Call Trace:
>[ 0.610063] ? dump_stack+0x5c/0x81
>[ 0.611118] ? kmem_cache_destroy+0x1aa/0x1c0
>[ 0.612632] ? acpi_sleep_proc_init+0x27/0x27
>[ 0.613906] ? acpi_os_delete_cache+0xa/0x10
>[ 0.617986] ? acpi_ut_delete_caches+0x3f/0x7b
>[ 0.619293] ? acpi_terminate+0xa/0x14
>[ 0.620394] ? acpi_init+0x2af/0x34f
>[ 0.621616] ? __class_create+0x4c/0x80
>[ 0.623412] ? video_setup+0x7f/0x7f
>[ 0.624585] ? acpi_sleep_proc_init+0x27/0x27
>[ 0.625861] ? do_one_initcall+0x4e/0x1a0
>[ 0.627513] ? kernel_init_freeable+0x19e/0x21f
>[ 0.628972] ? rest_init+0x80/0x80
>[ 0.630043] ? kernel_init+0xa/0x100
>[ 0.631084] ? ret_from_fork+0x25/0x30
>[ 0.633343] vgaarb: loaded
>[ 0.635036] EDAC MC: Ver: 3.0.0
>[ 0.638601] PCI: Probing PCI hardware
>[ 0.639833] PCI host bridge to bus 0000:00
>[ 0.641031] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
> ... Continue to boot and log is omitted ...
I analyzed this memory leak in detail and found acpi_ds_obj_stack_pop_and_
delete() function miscalculated the top of the stack. acpi_ds_obj_stack_push()
function uses walk_state->operand_index for start position of the top, but
acpi_ds_obj_stack_pop_and_delete() function considers index 0 for it.
Therefore, this causes acpi operand memory leak.
This cache leak causes a security threat because an old kernel (<= 4.9) shows
memory locations of kernel functions in stack dump. Some malicious users
could use this information to neutralize kernel ASLR.
I made a patch to fix ACPI operand cache leak. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPICA: fix acpi parse and parseext cache leaks
ACPICA commit 8829e70e1360c81e7a5a901b5d4f48330e021ea5
I'm Seunghun Han, and I work for National Security Research Institute of
South Korea.
I have been doing a research on ACPI and found an ACPI cache leak in ACPI
early abort cases.
Boot log of ACPI cache leak is as follows:
[ 0.352414] ACPI: Added _OSI(Module Device)
[ 0.353182] ACPI: Added _OSI(Processor Device)
[ 0.353182] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.353182] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.356028] ACPI: Unable to start the ACPI Interpreter
[ 0.356799] ACPI Error: Could not remove SCI handler (20170303/evmisc-281)
[ 0.360215] kmem_cache_destroy Acpi-State: Slab cache still has objects
[ 0.360648] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W
4.12.0-rc4-next-20170608+ #10
[ 0.361273] Hardware name: innotek gmb_h virtual_box/virtual_box, BIOS
virtual_box 12/01/2006
[ 0.361873] Call Trace:
[ 0.362243] ? dump_stack+0x5c/0x81
[ 0.362591] ? kmem_cache_destroy+0x1aa/0x1c0
[ 0.362944] ? acpi_sleep_proc_init+0x27/0x27
[ 0.363296] ? acpi_os_delete_cache+0xa/0x10
[ 0.363646] ? acpi_ut_delete_caches+0x6d/0x7b
[ 0.364000] ? acpi_terminate+0xa/0x14
[ 0.364000] ? acpi_init+0x2af/0x34f
[ 0.364000] ? __class_create+0x4c/0x80
[ 0.364000] ? video_setup+0x7f/0x7f
[ 0.364000] ? acpi_sleep_proc_init+0x27/0x27
[ 0.364000] ? do_one_initcall+0x4e/0x1a0
[ 0.364000] ? kernel_init_freeable+0x189/0x20a
[ 0.364000] ? rest_init+0xc0/0xc0
[ 0.364000] ? kernel_init+0xa/0x100
[ 0.364000] ? ret_from_fork+0x25/0x30
I analyzed this memory leak in detail. I found that “Acpi-State” cache and
“Acpi-Parse” cache were merged because the size of cache objects was same
slab cache size.
I finally found “Acpi-Parse” cache and “Acpi-parse_ext” cache were leaked
using SLAB_NEVER_MERGE flag in kmem_cache_create() function.
Real ACPI cache leak point is as follows:
[ 0.360101] ACPI: Added _OSI(Module Device)
[ 0.360101] ACPI: Added _OSI(Processor Device)
[ 0.360101] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.361043] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.364016] ACPI: Unable to start the ACPI Interpreter
[ 0.365061] ACPI Error: Could not remove SCI handler (20170303/evmisc-281)
[ 0.368174] kmem_cache_destroy Acpi-Parse: Slab cache still has objects
[ 0.369332] CPU: 1 PID: 1 Comm: swapper/0 Tainted: G W
4.12.0-rc4-next-20170608+ #8
[ 0.371256] Hardware name: innotek gmb_h virtual_box/virtual_box, BIOS
virtual_box 12/01/2006
[ 0.372000] Call Trace:
[ 0.372000] ? dump_stack+0x5c/0x81
[ 0.372000] ? kmem_cache_destroy+0x1aa/0x1c0
[ 0.372000] ? acpi_sleep_proc_init+0x27/0x27
[ 0.372000] ? acpi_os_delete_cache+0xa/0x10
[ 0.372000] ? acpi_ut_delete_caches+0x56/0x7b
[ 0.372000] ? acpi_terminate+0xa/0x14
[ 0.372000] ? acpi_init+0x2af/0x34f
[ 0.372000] ? __class_create+0x4c/0x80
[ 0.372000] ? video_setup+0x7f/0x7f
[ 0.372000] ? acpi_sleep_proc_init+0x27/0x27
[ 0.372000] ? do_one_initcall+0x4e/0x1a0
[ 0.372000] ? kernel_init_freeable+0x189/0x20a
[ 0.372000] ? rest_init+0xc0/0xc0
[ 0.372000] ? kernel_init+0xa/0x100
[ 0.372000] ? ret_from_fork+0x25/0x30
[ 0.388039] kmem_cache_destroy Acpi-parse_ext: Slab cache still has objects
[ 0.389063] CPU: 1 PID: 1 Comm: swapper/0 Tainted: G W
4.12.0-rc4-next-20170608+ #8
[ 0.390557] Hardware name: innotek gmb_h virtual_box/virtual_box, BIOS
virtual_box 12/01/2006
[ 0.392000] Call Trace:
[ 0.392000] ? dump_stack+0x5c/0x81
[ 0.392000] ? kmem_cache_destroy+0x1aa/0x1c0
[ 0.392000] ? acpi_sleep_proc_init+0x27/0x27
[ 0.392000] ? acpi_os_delete_cache+0xa/0x10
[ 0.392000] ? acpi_ut_delete_caches+0x6d/0x7b
[ 0.392000] ? acpi_terminate+0xa/0x14
[ 0.392000] ? acpi_init+0x2af/0x3
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
qibfs: fix _another_ leak
failure to allocate inode => leaked dentry...
this one had been there since the initial merge; to be fair,
if we are that far OOM, the odds of failing at that particular
allocation are low... |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: Fix a fence leak in submit error path
In error paths, we could unref the submit without calling
drm_sched_entity_push_job(), so msm_job_free() will never get
called. Since drm_sched_job_cleanup() will NULL out the
s_fence, we can use that to detect this case.
Patchwork: https://patchwork.freedesktop.org/patch/653584/ |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: Fix another leak in the submit error path
put_unused_fd() doesn't free the installed file, if we've already done
fd_install(). So we need to also free the sync_file.
Patchwork: https://patchwork.freedesktop.org/patch/653583/ |
| In the Linux kernel, the following vulnerability has been resolved:
remoteproc: core: Release rproc->clean_table after rproc_attach() fails
When rproc->state = RPROC_DETACHED is attached to remote processor
through rproc_attach(), if rproc_handle_resources() returns failure,
then the clean table should be released, otherwise the following
memory leak will occur.
unreferenced object 0xffff000086a99800 (size 1024):
comm "kworker/u12:3", pid 59, jiffies 4294893670 (age 121.140s)
hex dump (first 32 bytes):
00 00 00 00 00 80 00 00 00 00 00 00 00 00 10 00 ............
00 00 00 00 00 00 08 00 00 00 00 00 00 00 00 00 ............
backtrace:
[<000000008bbe4ca8>] slab_post_alloc_hook+0x98/0x3fc
[<000000003b8a272b>] __kmem_cache_alloc_node+0x13c/0x230
[<000000007a507c51>] __kmalloc_node_track_caller+0x5c/0x260
[<0000000037818dae>] kmemdup+0x34/0x60
[<00000000610f7f57>] rproc_boot+0x35c/0x56c
[<0000000065f8871a>] rproc_add+0x124/0x17c
[<00000000497416ee>] imx_rproc_probe+0x4ec/0x5d4
[<000000003bcaa37d>] platform_probe+0x68/0xd8
[<00000000771577f9>] really_probe+0x110/0x27c
[<00000000531fea59>] __driver_probe_device+0x78/0x12c
[<0000000080036a04>] driver_probe_device+0x3c/0x118
[<000000007e0bddcb>] __device_attach_driver+0xb8/0xf8
[<000000000cf1fa33>] bus_for_each_drv+0x84/0xe4
[<000000001a53b53e>] __device_attach+0xfc/0x18c
[<00000000d1a2a32c>] device_initial_probe+0x14/0x20
[<00000000d8f8b7ae>] bus_probe_device+0xb0/0xb4
unreferenced object 0xffff0000864c9690 (size 16): |
| In the Linux kernel, the following vulnerability has been resolved:
remoteproc: core: Cleanup acquired resources when rproc_handle_resources() fails in rproc_attach()
When rproc->state = RPROC_DETACHED and rproc_attach() is used
to attach to the remote processor, if rproc_handle_resources()
returns a failure, the resources allocated by imx_rproc_prepare()
should be released, otherwise the following memory leak will occur.
Since almost the same thing is done in imx_rproc_prepare() and
rproc_resource_cleanup(), Function rproc_resource_cleanup() is able
to deal with empty lists so it is better to fix the "goto" statements
in rproc_attach(). replace the "unprepare_device" goto statement with
"clean_up_resources" and get rid of the "unprepare_device" label.
unreferenced object 0xffff0000861c5d00 (size 128):
comm "kworker/u12:3", pid 59, jiffies 4294893509 (age 149.220s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 02 88 00 00 00 00 00 00 10 00 00 00 00 00 ............
backtrace:
[<00000000f949fe18>] slab_post_alloc_hook+0x98/0x37c
[<00000000adbfb3e7>] __kmem_cache_alloc_node+0x138/0x2e0
[<00000000521c0345>] kmalloc_trace+0x40/0x158
[<000000004e330a49>] rproc_mem_entry_init+0x60/0xf8
[<000000002815755e>] imx_rproc_prepare+0xe0/0x180
[<0000000003f61b4e>] rproc_boot+0x2ec/0x528
[<00000000e7e994ac>] rproc_add+0x124/0x17c
[<0000000048594076>] imx_rproc_probe+0x4ec/0x5d4
[<00000000efc298a1>] platform_probe+0x68/0xd8
[<00000000110be6fe>] really_probe+0x110/0x27c
[<00000000e245c0ae>] __driver_probe_device+0x78/0x12c
[<00000000f61f6f5e>] driver_probe_device+0x3c/0x118
[<00000000a7874938>] __device_attach_driver+0xb8/0xf8
[<0000000065319e69>] bus_for_each_drv+0x84/0xe4
[<00000000db3eb243>] __device_attach+0xfc/0x18c
[<0000000072e4e1a4>] device_initial_probe+0x14/0x20 |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: fix small mempool leak in SMB2_negotiate()
In some cases of failure (dialect mismatches) in SMB2_negotiate(), after
the request is sent, the checks would return -EIO when they should be
rather setting rc = -EIO and jumping to neg_exit to free the response
buffer from mempool. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: hda: fix potential memleak in 'add_widget_node'
As 'kobject_add' may allocated memory for 'kobject->name' when return error.
And in this function, if call 'kobject_add' failed didn't free kobject.
So call 'kobject_put' to recycling resources. |
| In the Linux kernel, the following vulnerability has been resolved:
hugetlbfs: don't delete error page from pagecache
This change is very similar to the change that was made for shmem [1], and
it solves the same problem but for HugeTLBFS instead.
Currently, when poison is found in a HugeTLB page, the page is removed
from the page cache. That means that attempting to map or read that
hugepage in the future will result in a new hugepage being allocated
instead of notifying the user that the page was poisoned. As [1] states,
this is effectively memory corruption.
The fix is to leave the page in the page cache. If the user attempts to
use a poisoned HugeTLB page with a syscall, the syscall will fail with
EIO, the same error code that shmem uses. For attempts to map the page,
the thread will get a BUS_MCEERR_AR SIGBUS.
[1]: commit a76054266661 ("mm: shmem: don't truncate page if memory failure happens") |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8712: fix a potential memory leak in r871xu_drv_init()
In r871xu_drv_init(), if r8712_init_drv_sw() fails, then the memory
allocated by r8712_alloc_io_queue() in r8712_usb_dvobj_init() is not
properly released as there is no action will be performed by
r8712_usb_dvobj_deinit().
To properly release it, we should call r8712_free_io_queue() in
r8712_usb_dvobj_deinit().
Besides, in r871xu_dev_remove(), r8712_usb_dvobj_deinit() will be called
by r871x_dev_unload() under condition `padapter->bup` and
r8712_free_io_queue() is called by r8712_free_drv_sw().
However, r8712_usb_dvobj_deinit() does not rely on `padapter->bup` and
calling r8712_free_io_queue() in r8712_free_drv_sw() is negative for
better understading the code.
So I move r8712_usb_dvobj_deinit() into r871xu_dev_remove(), and remove
r8712_free_io_queue() from r8712_free_drv_sw(). |
| In the Linux kernel, the following vulnerability has been resolved:
raid10: cleanup memleak at raid10_make_request
If raid10_read_request or raid10_write_request registers a new
request and the REQ_NOWAIT flag is set, the code does not
free the malloc from the mempool.
unreferenced object 0xffff8884802c3200 (size 192):
comm "fio", pid 9197, jiffies 4298078271
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 88 41 02 00 00 00 00 00 .........A......
08 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc c1a049a2):
__kmalloc+0x2bb/0x450
mempool_alloc+0x11b/0x320
raid10_make_request+0x19e/0x650 [raid10]
md_handle_request+0x3b3/0x9e0
__submit_bio+0x394/0x560
__submit_bio_noacct+0x145/0x530
submit_bio_noacct_nocheck+0x682/0x830
__blkdev_direct_IO_async+0x4dc/0x6b0
blkdev_read_iter+0x1e5/0x3b0
__io_read+0x230/0x1110
io_read+0x13/0x30
io_issue_sqe+0x134/0x1180
io_submit_sqes+0x48c/0xe90
__do_sys_io_uring_enter+0x574/0x8b0
do_syscall_64+0x5c/0xe0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
V4: changing backing tree to see if CKI tests will pass.
The patch code has not changed between any versions. |
| In the Linux kernel, the following vulnerability has been resolved:
netlink: Fix wraparounds of sk->sk_rmem_alloc.
Netlink has this pattern in some places
if (atomic_read(&sk->sk_rmem_alloc) > sk->sk_rcvbuf)
atomic_add(skb->truesize, &sk->sk_rmem_alloc);
, which has the same problem fixed by commit 5a465a0da13e ("udp:
Fix multiple wraparounds of sk->sk_rmem_alloc.").
For example, if we set INT_MAX to SO_RCVBUFFORCE, the condition
is always false as the two operands are of int.
Then, a single socket can eat as many skb as possible until OOM
happens, and we can see multiple wraparounds of sk->sk_rmem_alloc.
Let's fix it by using atomic_add_return() and comparing the two
variables as unsigned int.
Before:
[root@fedora ~]# ss -f netlink
Recv-Q Send-Q Local Address:Port Peer Address:Port
-1668710080 0 rtnl:nl_wraparound/293 *
After:
[root@fedora ~]# ss -f netlink
Recv-Q Send-Q Local Address:Port Peer Address:Port
2147483072 0 rtnl:nl_wraparound/290 *
^
`--- INT_MAX - 576 |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: sun8i-ce-cipher - fix error handling in sun8i_ce_cipher_prepare()
Fix two DMA cleanup issues on the error path in sun8i_ce_cipher_prepare():
1] If dma_map_sg() fails for areq->dst, the device driver would try to free
DMA memory it has not allocated in the first place. To fix this, on the
"theend_sgs" error path, call dma unmap only if the corresponding dma
map was successful.
2] If the dma_map_single() call for the IV fails, the device driver would
try to free an invalid DMA memory address on the "theend_iv" path:
------------[ cut here ]------------
DMA-API: sun8i-ce 1904000.crypto: device driver tries to free an invalid DMA memory address
WARNING: CPU: 2 PID: 69 at kernel/dma/debug.c:968 check_unmap+0x123c/0x1b90
Modules linked in: skcipher_example(O+)
CPU: 2 UID: 0 PID: 69 Comm: 1904000.crypto- Tainted: G O 6.15.0-rc3+ #24 PREEMPT
Tainted: [O]=OOT_MODULE
Hardware name: OrangePi Zero2 (DT)
pc : check_unmap+0x123c/0x1b90
lr : check_unmap+0x123c/0x1b90
...
Call trace:
check_unmap+0x123c/0x1b90 (P)
debug_dma_unmap_page+0xac/0xc0
dma_unmap_page_attrs+0x1f4/0x5fc
sun8i_ce_cipher_do_one+0x1bd4/0x1f40
crypto_pump_work+0x334/0x6e0
kthread_worker_fn+0x21c/0x438
kthread+0x374/0x664
ret_from_fork+0x10/0x20
---[ end trace 0000000000000000 ]---
To fix this, check for !dma_mapping_error() before calling
dma_unmap_single() on the "theend_iv" path. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: mscc: Fix memory leak when using one step timestamping
Fix memory leak when running one-step timestamping. When running
one-step sync timestamping, the HW is configured to insert the TX time
into the frame, so there is no reason to keep the skb anymore. As in
this case the HW will never generate an interrupt to say that the frame
was timestamped, then the frame will never released.
Fix this by freeing the frame in case of one-step timestamping. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, sockmap: Fix panic when calling skb_linearize
The panic can be reproduced by executing the command:
./bench sockmap -c 2 -p 1 -a --rx-verdict-ingress --rx-strp 100000
Then a kernel panic was captured:
'''
[ 657.460555] kernel BUG at net/core/skbuff.c:2178!
[ 657.462680] Tainted: [W]=WARN
[ 657.463287] Workqueue: events sk_psock_backlog
...
[ 657.469610] <TASK>
[ 657.469738] ? die+0x36/0x90
[ 657.469916] ? do_trap+0x1d0/0x270
[ 657.470118] ? pskb_expand_head+0x612/0xf40
[ 657.470376] ? pskb_expand_head+0x612/0xf40
[ 657.470620] ? do_error_trap+0xa3/0x170
[ 657.470846] ? pskb_expand_head+0x612/0xf40
[ 657.471092] ? handle_invalid_op+0x2c/0x40
[ 657.471335] ? pskb_expand_head+0x612/0xf40
[ 657.471579] ? exc_invalid_op+0x2d/0x40
[ 657.471805] ? asm_exc_invalid_op+0x1a/0x20
[ 657.472052] ? pskb_expand_head+0xd1/0xf40
[ 657.472292] ? pskb_expand_head+0x612/0xf40
[ 657.472540] ? lock_acquire+0x18f/0x4e0
[ 657.472766] ? find_held_lock+0x2d/0x110
[ 657.472999] ? __pfx_pskb_expand_head+0x10/0x10
[ 657.473263] ? __kmalloc_cache_noprof+0x5b/0x470
[ 657.473537] ? __pfx___lock_release.isra.0+0x10/0x10
[ 657.473826] __pskb_pull_tail+0xfd/0x1d20
[ 657.474062] ? __kasan_slab_alloc+0x4e/0x90
[ 657.474707] sk_psock_skb_ingress_enqueue+0x3bf/0x510
[ 657.475392] ? __kasan_kmalloc+0xaa/0xb0
[ 657.476010] sk_psock_backlog+0x5cf/0xd70
[ 657.476637] process_one_work+0x858/0x1a20
'''
The panic originates from the assertion BUG_ON(skb_shared(skb)) in
skb_linearize(). A previous commit(see Fixes tag) introduced skb_get()
to avoid race conditions between skb operations in the backlog and skb
release in the recvmsg path. However, this caused the panic to always
occur when skb_linearize is executed.
The "--rx-strp 100000" parameter forces the RX path to use the strparser
module which aggregates data until it reaches 100KB before calling sockmap
logic. The 100KB payload exceeds MAX_MSG_FRAGS, triggering skb_linearize.
To fix this issue, just move skb_get into sk_psock_skb_ingress_enqueue.
'''
sk_psock_backlog:
sk_psock_handle_skb
skb_get(skb) <== we move it into 'sk_psock_skb_ingress_enqueue'
sk_psock_skb_ingress____________
↓
|
| → sk_psock_skb_ingress_self
| sk_psock_skb_ingress_enqueue
sk_psock_verdict_apply_________________↑ skb_linearize
'''
Note that for verdict_apply path, the skb_get operation is unnecessary so
we add 'take_ref' param to control it's behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
atm: atmtcp: Free invalid length skb in atmtcp_c_send().
syzbot reported the splat below. [0]
vcc_sendmsg() copies data passed from userspace to skb and passes
it to vcc->dev->ops->send().
atmtcp_c_send() accesses skb->data as struct atmtcp_hdr after
checking if skb->len is 0, but it's not enough.
Also, when skb->len == 0, skb and sk (vcc) were leaked because
dev_kfree_skb() is not called and sk_wmem_alloc adjustment is missing
to revert atm_account_tx() in vcc_sendmsg(), which is expected
to be done in atm_pop_raw().
Let's properly free skb with an invalid length in atmtcp_c_send().
[0]:
BUG: KMSAN: uninit-value in atmtcp_c_send+0x255/0xed0 drivers/atm/atmtcp.c:294
atmtcp_c_send+0x255/0xed0 drivers/atm/atmtcp.c:294
vcc_sendmsg+0xd7c/0xff0 net/atm/common.c:644
sock_sendmsg_nosec net/socket.c:712 [inline]
__sock_sendmsg+0x330/0x3d0 net/socket.c:727
____sys_sendmsg+0x7e0/0xd80 net/socket.c:2566
___sys_sendmsg+0x271/0x3b0 net/socket.c:2620
__sys_sendmsg net/socket.c:2652 [inline]
__do_sys_sendmsg net/socket.c:2657 [inline]
__se_sys_sendmsg net/socket.c:2655 [inline]
__x64_sys_sendmsg+0x211/0x3e0 net/socket.c:2655
x64_sys_call+0x32fb/0x3db0 arch/x86/include/generated/asm/syscalls_64.h:47
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xd9/0x210 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Uninit was created at:
slab_post_alloc_hook mm/slub.c:4154 [inline]
slab_alloc_node mm/slub.c:4197 [inline]
kmem_cache_alloc_node_noprof+0x818/0xf00 mm/slub.c:4249
kmalloc_reserve+0x13c/0x4b0 net/core/skbuff.c:579
__alloc_skb+0x347/0x7d0 net/core/skbuff.c:670
alloc_skb include/linux/skbuff.h:1336 [inline]
vcc_sendmsg+0xb40/0xff0 net/atm/common.c:628
sock_sendmsg_nosec net/socket.c:712 [inline]
__sock_sendmsg+0x330/0x3d0 net/socket.c:727
____sys_sendmsg+0x7e0/0xd80 net/socket.c:2566
___sys_sendmsg+0x271/0x3b0 net/socket.c:2620
__sys_sendmsg net/socket.c:2652 [inline]
__do_sys_sendmsg net/socket.c:2657 [inline]
__se_sys_sendmsg net/socket.c:2655 [inline]
__x64_sys_sendmsg+0x211/0x3e0 net/socket.c:2655
x64_sys_call+0x32fb/0x3db0 arch/x86/include/generated/asm/syscalls_64.h:47
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xd9/0x210 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
CPU: 1 UID: 0 PID: 5798 Comm: syz-executor192 Not tainted 6.16.0-rc1-syzkaller-00010-g2c4a1f3fe03e #0 PREEMPT(undef)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/07/2025 |
